Quick Answer: An angled cone adapter is a glass fitting with a ground-glass cone at one end and a tube bent at an angle at the other, usually finished for rubber tubing. It plugs into a socket and leads a gas, vacuum or vent line away sideways, so the tubing does not rise straight up from the apparatus.
Why the Connection Is Bent
A straight adapter sends tubing directly out along the axis of the joint. That is awkward at the top of a reflux condenser or on a vertical flask neck, where tubing standing straight up is easily knocked, pulls on the joint and can kink. Bending the connection to the side lets the tubing run down to a bubbler, trap or gas supply along the frame, with less leverage on the ground joint.
Typical positions are the top of a reflux condenser, where the adapter leads acid fumes or displaced air to a trap; a side neck of a multi-neck flask, where it brings in nitrogen; and the end of a set-up where a vent to the fume cupboard is needed. The cone end seals like any other ground joint, with a thin band of grease or a PTFE sleeve and a joint clip.
When the line must be opened and closed at the adapter itself, the right-angle cone adapter with stopcock adds a tap. Sizes are marked on the cone and should match the socket it goes into.
Care & Handling
- Support the tubing separately with a clamp or clip so its weight does not lever the adapter out of the joint.
- Push tubing onto the glass end with a twisting action after wetting it; forcing it straight on can snap the tube.
- Never close off a vent adapter on a heated system; there must always be an open path for expanding gas.
- Remove the adapter and clean the cone after each use so grease does not harden in the joint.
Specifications
| Joint end | Ground-glass cone |
| Other end | Tube bent at an angle, typically finished for rubber tubing |
| Function | Leads gas, vacuum or vent lines sideways from a socket |
| Seal | Light grease or PTFE sleeve, secured with a joint clip |
Applications
- Venting the top of a reflux condenser to a gas trap or bubbler
- Feeding nitrogen or another inert gas into a side neck of a reaction flask
- Connecting a flask to a water filter pump for gentle evacuation
- Routing tubing tidily in teaching assemblies where upright lines would be knocked
Why Choose LabEquip
Research groups and college organic labs use angled cone adapters to plumb inert-gas and vent lines neatly into their ground-joint glassware. The fitting is available through LabEquip’s chemistry lab equipment catalogue; send the joint size and tubing diameter through the contact page.
Related Products
- Cone Adapters, Straight Connection: A straight cone adapter for sockets that already point sideways.
- Cone Adapters, Right Angle Connection With Stop-cock: A right-angle cone adapter with stopcock for opening or closing the line at the joint.
- Socket To Cone With T Connection Adapters: A socket-to-cone adapter with T connection, adding a side tube between two joints.
- Miscellaneous Fittings: Miscellaneous fittings including joint clips, T-pieces and connectors.
Frequently Asked Questions
What is an angled cone adapter used for?
It is a glass fitting with a ground-glass cone at one end and a tube bent at an angle at the other, usually finished for rubber tubing. It plugs into a socket and leads a gas, vacuum or vent line away to the side.
Why use an angled adapter instead of a straight one on a condenser top?
Tubing rising straight up from a reflux condenser or vertical neck is easily knocked, pulls on the joint and can kink. An angled connection lets the tubing run down the frame to a bubbler, trap or gas supply with less strain on the glass.
How do you attach tubing to a glass cone adapter safely?
Wet the tube end with a little water or glycerol and push the tubing on with a gentle twist, holding the glass close to the end. Protect your hand with a cloth, since pushing on a glass tube is a common cause of cuts.
How is an angled cone adapter sealed in its socket?
Use a light film of grease or a PTFE sleeve on the cone and secure it with a joint clip, as noted in the specifications. This keeps the joint gas-tight and stops it working loose when tubing is moved.
What can be connected to the side tube of a cone adapter?
Typical connections are an inert gas line, a vacuum line, a drying tube or a bubbler that shows gas flow. The adapter makes these connections without changing the main glass assembly.
How do you choose the right size of cone adapter?
Match the cone to the socket it will sit in, using the joint size marked on the socket, and check that the tube end suits the bore of your tubing. The bend angle should suit how the tubing will be routed.
Last Updated: November 2026









Reviews
There are no reviews yet.