Search

In Stock

Battery Eliminator

Adjustable Voltage Output: Allows precise control of DC voltage to accommodate various electrical experiments and devices.

Overload Protection: Integrated safety features prevent short circuits and damage to connected equipment during lab activities.

$4.15

Quick Answer: The Battery Eliminator is a mains-powered low-voltage DC supply used in school and college laboratories in place of dry cells. A battery eliminator steps the mains voltage down, rectifies it and smooths it, so circuits get a steady direct current supply that does not run down during a practical.

Inside a Mains-to-DC Supply

Three stages do the work. A step-down transformer reduces the mains voltage to a safe low value and isolates the output from the mains. A rectifier, usually a bridge of four diodes, turns the alternating output into current that flows in one direction only, though still in pulses. A smoothing capacitor then fills the gaps between pulses so the output approaches a steady DC level. Some designs add a regulator to hold the voltage steady as the load changes, and some offer selectable outputs; which features a particular model has should be confirmed before ordering.

In a simple unregulated supply, the output voltage falls a little as more current is drawn and a small ripple remains. For most school circuits this does not matter, and measuring the actual voltage across the circuit with a voltmeter is good practice anyway.

Why Replace Dry Cells

Dry cells lose voltage as they are used and their internal resistance rises, so a practical that starts with a bright lamp can end with a dim one, and readings drift. An eliminator gives the same supply from the first reading to the last, and over a school year it removes the cost and disposal of large numbers of spent cells. Cells still have a place in experiments about cells themselves, such as measuring internal resistance.

Practicals Powered by an Eliminator

  • Ohm’s law and resistance practicals with an ammeter and voltmeter
  • Lighting a 6 V lamp in series and parallel circuit work
  • Powering electromagnets, relays and electric bell demonstrations
  • Supplying current for electrolysis and electroplating experiments
  • Running circuits with a nichrome rheostat to vary current

Specifications

Function Converts mains AC to low-voltage DC
Stages Step-down transformer, rectifier, smoothing
Replaces Dry cells in low-voltage teaching circuits
Connection Output terminals for circuit leads
Output voltages, current rating and regulation Confirm at enquiry

Care & Handling

  • Switch the eliminator off and set the lowest output before connecting or changing a circuit.
  • Check the mains cable and plug for damage before use, and keep the unit away from water.
  • Include a resistor, lamp or rheostat in every circuit; never join the output terminals directly.
  • Let only the teacher handle the mains connection, and do not open the case.

Why Choose LabEquip

Schools moving away from dry cells buy one eliminator per bench, which is a sensible first purchase alongside electricity experiment kits for schools since every circuit practical then shares the same steady supply. LabEquip lists battery eliminators among its physics equipment, and the output range needed for a syllabus can be discussed on the contact page.

Frequently Asked Questions

What is the difference between a battery eliminator and a battery?

A battery stores chemical energy and its voltage falls as it is used. An eliminator takes energy from the mains and converts it to low-voltage DC, giving a steady supply for as long as it is switched on.

Why does the output voltage change when the circuit changes?

In a simple unregulated eliminator, drawing more current lowers the output slightly because of resistance in the transformer and rectifier. Measure the voltage across the circuit itself rather than relying on the dial.

Is the output of an eliminator pure DC?

Not completely. After rectification and smoothing a small ripple remains, which is unimportant for lamps, motors and most meters. Regulated supplies reduce this ripple further.

Can students use an eliminator safely?

Yes, at its low-voltage output terminals, under supervision. The teacher should handle the mains connection, check the cable and plug, and make sure every circuit includes a load or resistor.

What happens if the output terminals are shorted?

A very large current flows, which can overheat the leads and damage the eliminator if it has no protection. Always build the circuit with a load in place before switching on.

Can an eliminator replace cells in every experiment?

Not in experiments about cells themselves, such as finding the internal resistance or comparing EMFs of cells. For most other low-voltage circuit work it is the more consistent choice.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
USD United States (US) dollar
Product has been added to your cart
Compare (0)