Search

In Stock

LAMP 6V

Rated operating voltage of 6 volts DC, compatible with standard laboratory power supplies

Durable filament design with controlled electrical characteristics, ensuring consistent illumination

₹190.00

Quick Answer: The Lamp 6V is a small filament lamp rated for 6 volts, used as the light-giving load in low-voltage school and college circuit practicals. A 6V lamp shows current flow visibly, compares series and parallel circuits by brightness, and is the standard example of a non-ohmic conductor.

How a Filament Lamp Works

Current through the thin coiled tungsten filament heats it until it glows. The filament sits inside a glass bulb that is evacuated or filled with an inert gas so the hot tungsten does not burn away. The 6 volt rating is the voltage at which the lamp is designed to run: below it the lamp glows dimly, and well above it the filament overheats and fails. The lamp’s power or current rating and its base type, screw or bayonet, should be matched to the holders already in use, and both should be confirmed when ordering.

The Lamp as a Non-Ohmic Conductor

Plot current against voltage for a lamp and the graph curves, bending towards the voltage axis. As the filament heats up its resistance rises, so each extra volt produces less extra current. Comparing this curve with the straight line given by a fixed resistor is one of the clearest ways to show that Ohm’s law describes some conductors and not others. Students take readings from zero to the rated 6 volts with a rheostat or variable supply, a 500 mA DC ammeter in series and a voltmeter across the lamp.

The same lamp makes series and parallel circuits visible. Two identical lamps in series share the supply voltage and glow dimly; in parallel each receives the full supply and glows brightly, and removing one leaves the other lit.

Circuit Practicals

  • Comparing lamp brightness in series and parallel circuits
  • Plotting the I-V characteristic of a filament lamp
  • Building a continuity or conductor and insulator tester
  • Calculating electrical power from voltage and current readings
  • Acting as an indicator in switch, relay and thermostat demonstrations

Specifications

Type Filament lamp
Rated voltage 6 V
Use Low-voltage teaching circuits
Mounting Fits a matching lamp holder on a board or base
Base type and power rating Confirm at enquiry

Care & Handling

  • Do not run the lamp above 6 volts; excess voltage shortens its life or blows the filament at once.
  • Let the lamp cool before removing it, as the glass becomes hot in use.
  • Screw or push the lamp firmly into its holder; a loose contact causes flicker and false readings.
  • Store spare lamps in a box so the glass and filaments are not knocked.

Why Choose LabEquip

Every school circuit practical uses lamps, and they are replaced often, so laboratories order them in quantity alongside bulb holders. LabEquip lists the 6V lamp among its physics equipment, and quantities can be arranged through the contact page.

Frequently Asked Questions

Why is a filament lamp called non-ohmic?

Its resistance increases as the filament heats up, so current is not proportional to voltage. The current-voltage graph is a curve rather than the straight line Ohm’s law predicts.

Why do two lamps in series glow more dimly than one?

In series the lamps share the supply voltage, so each receives less than its rated voltage and less current flows. In parallel each lamp gets the full supply voltage.

What happens if the lamp is connected to more than 6 volts?

The filament runs hotter than designed, glows very brightly for a short time and then breaks. Always set the supply to 6 volts or below.

Can the lamp be used with a battery eliminator?

Yes, if the eliminator output is set to 6 volts or less. Check the voltage across the lamp with a voltmeter, since unregulated eliminators can give more than their dial setting at light load.

Why does the lamp glow before reaching full brightness?

At low voltage the filament is warm but not hot enough to glow brightly. Brightness rises steeply as the filament temperature increases towards its operating value.

How do I know which holder the lamp fits?

Lamps use either screw or bayonet bases of particular sizes. Match the base to the holders on your circuit boards, and confirm the base type when ordering.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
INR Indian rupee
Product has been added to your cart
Compare (0)