Quick Answer: Submersible resistors are resistors built to be immersed in water or another liquid so that the heat they produce can be measured in a calorimeter. They are used for electrical heating experiments, for comparing the heat produced by different resistances and for calibrating the heat capacity of a calorimeter.
Comparing Resistors in Series and in Parallel
With two submersible resistors of different values, each in its own calorimeter with equal masses of water, the circuit arrangement decides which one heats faster. Connected in series, both carry the same current, and since P = I²R the larger resistance produces more heat. Connected in parallel, both have the same voltage across them, and since P = V²/R the smaller resistance produces more heat.
This pair of results surprises many students, who expect a bigger resistor always to get hotter. Measuring the temperature rises in both arrangements, and comparing their ratio with the ratio of the resistances, turns a common misconception into a quantitative test.
Electrical Calibration of a Calorimeter
Electrical heating is the most precise way to put a known amount of energy into a calorimeter. With a submersible resistor in the water, voltage V, current I and time t give the energy E = VIt directly. The temperature rise then gives the total heat capacity of water plus vessel, and subtracting the water’s share leaves the heat capacity of the calorimeter itself.
Because the energy is measured electrically rather than inferred from another temperature reading, this calibration avoids the transfer losses of the hot-water mixing method. Once calibrated, the same calorimeter can be used for reaction, solution or mixing experiments with more confidence. The resistance values and power ratings of this set should be taken from the resistors’ markings or data, not assumed.
Specifications
| Product | Set of submersible resistors for calorimetry |
| Use | Electrical heating of liquids in calorimeters |
| Key relations | P = I²R in series, P = V²/R in parallel, E = VIt |
| Experiments | Heating in series and parallel, calorimeter calibration, specific heat capacity of liquids |
| Resistance values, number supplied and power rating | Confirm at enquiry |
Experiments
- Comparing heat produced by two resistances in series and in parallel
- Calibrating the heat capacity of a calorimeter electrically
- Measuring the specific heat capacity of water or oil
- Testing Joule’s law with a known resistance
Care & Handling
- Switch on only when the resistor is fully immersed, and switch off before lifting it out of the liquid
- Keep the terminals and leads above the liquid surface and dry
- Stay within the voltage and current rating marked for each resistor
- Rinse in clean water after use and let it dry before storage
Why Choose LabEquip
Teachers buy submersible resistors to add electrical heating to calorimeters they already have, for Joule’s law and calibration practicals. They pair with the Joule effect model and fit calorimeters such as the small model calorimeter; contact LabEquip to confirm values and ratings.
Frequently Asked Questions
Why does the larger resistor heat more in series but less in parallel?
In series both resistors carry the same current, so the heating power I²R is greater for the larger resistance. In parallel both have the same voltage, so the power V²/R is greater for the smaller resistance.
Can a submersible resistor be switched on in air?
It should not be. It is designed to shed heat into a liquid, and in air it can overheat quickly and damage its insulation or seals.
How do the resistors help calibrate a calorimeter?
The electrical energy supplied is known exactly from voltage, current and time. Dividing it by the temperature rise gives the total heat capacity, from which the calorimeter’s own share is found.
Which liquids can the resistors be used in?
Water is the usual choice. Other liquids such as oils can be used for specific heat comparisons, provided they do not attack the resistor’s covering; avoid flammable liquids.
Why use equal masses of water in each calorimeter?
With equal masses and identical vessels, the temperature rises are directly proportional to the heat produced. The ratio of the rises then compares the heating of the two resistors without further calculation.
Should the water be stirred during heating?
Yes. Warm water rises from the resistor and forms layers, so stirring keeps the temperature uniform and makes the thermometer reading represent the whole volume.
Last Updated: October 2026










Reviews
There are no reviews yet.