Quick Answer: A shock detector is a sensor that responds to the jolt of an impact and turns it into an electrical signal. Connected to an electronic timer or data-logging interface, it marks the exact moment a falling ball lands, a projectile hits the floor or two objects collide, so the time can be measured without human reaction time.
Taking Reaction Time Out of the Measurement
Human reaction time is around 0.2 s, while a ball dropped from one metre lands after about 0.45 s. Stopping a stopwatch by eye therefore adds an error close to half the measurement. The detector stops the timer at the instant of impact, so the timing error falls to a tiny fraction of that. The same signal can start a timer instead of stopping it, for example when a collision begins a sequence of measurements.
In a free-fall set-up the electromagnet release starts the clock and the ball striking the detector stops it. In projectile work the detector can be placed where the projectile lands, giving the time of flight to compare with the prediction t = 2v sin θ/g for level ground.
Two Detectors and the Speed of Sound in a Metal
Clamp a long metal rod horizontally with a detector touching each end, and tap one end sharply. The disturbance runs along the rod as a sound wave and reaches the far detector a short time later. Dividing the rod’s length by that delay gives the speed of sound in the metal, several thousand metres per second, which means a delay of well under a millisecond for a one-metre rod. The experiment needs a timer that resolves such short times, but it makes a striking comparison with the speed of sound in air.
Specifications
| Function | Senses an impact and outputs a timing signal |
| Typical role | Stop or start signal for an electronic timer or interface |
| Paired with | Free-fall release, projectile launcher, collision carts |
| Advantage | Removes human reaction time from short timings |
| Sensing element, output and connections | Confirm at enquiry |
Applications
- Stopping the timer when a free-fall ball lands, to measure g
- Measuring a projectile’s time of flight from launch to landing
- Marking the instant of collision between carts or balls
- Timing a sound pulse along a metal rod with two detectors
Care & Handling
- Let only the target area take the impacts; do not strike the body or the lead.
- Stand the detector on a firm surface away from other vibrations, which can trigger it falsely.
- Use the light balls and moderate impacts the experiment needs rather than heavy blows.
- Coil the lead loosely and keep the connector clean and dry.
Why Choose LabEquip
Physics teachers add this impact sensor when they want timing results that reflect the physics rather than how quickly someone pressed a button. LabEquip lists it in its physics lab equipment range alongside the ball for free fall and the ballistic projectile launcher it often works with. Ask through the contact page which timers and interfaces it connects to.
Frequently Asked Questions
Why use a shock detector instead of a stopwatch?
Human reaction time adds roughly 0.2 s at each press of a stopwatch, which is comparable to the fall times being measured. The detector stops the timer at the instant of impact, so the timing error becomes very small.
How does it work with free-fall apparatus?
The electromagnet release starts the electronic timer as the ball is let go, and the ball striking the detector at the bottom stops it. The time and the measured height then give g.
Why does the timer sometimes stop too early?
The detector can respond to other jolts, such as a bench being knocked or a door slamming. Stand it on a firm surface away from other activity and keep hands off the bench during the drop.
Can two detectors measure the speed of sound in a metal rod?
Yes, with a fast timer. Place a detector at each end of the rod and tap one end. The rod’s length divided by the delay between the two signals gives the speed of sound in the metal.
Can it time how long a projectile is in the air?
Yes. Start the timer at launch and place the detector where the projectile lands. The measured time of flight can then be compared with the value predicted from launch speed and angle.
How should the detector be protected?
Only the target area should be struck, and only with the light balls or carts the experiment uses. Avoid heavy blows, keep the lead out of the impact zone and store it dry.
Last Updated: October 2026










Reviews
There are no reviews yet.