Quick Answer: A set of 3 mechanical balls is a group of three balls for mechanics experiments, used to compare how objects of different mass, size or material behave when they roll, fall, bounce or collide. Teachers use the set of 3 mechanical balls across several practicals, from rolling races on tracks to collisions and coefficient-of-restitution tests.
Measuring the Balls First
Before any race or collision, the balls themselves make a short measurement exercise. Weigh each one on a balance and measure its diameter with vernier calipers, taking readings across two or three diameters to check it is round. The density follows from ρ = m ÷ (πd³/6). Comparing the three densities with tables of common materials lets students identify what each ball is made of and predicts which will be least affected by air resistance.
Collisions and Bounces
A moving ball striking a stationary ball of equal mass head-on stops almost dead, and the target moves off with nearly all the speed, the effect behind a Newton’s cradle. If the moving ball is lighter than the target, it bounces back; if heavier, both continue forwards. Comparing these three cases with the predictions of momentum conservation shows how mass decides the outcome.
Dropping each ball onto a hard floor from a measured height h₁ and recording the rebound height h₂ gives the coefficient of restitution e = √(h₂/h₁). Values near 1 mean a very elastic bounce; low values show that much of the energy turns into heat and sound. The three balls usually give clearly different results, which makes the comparison worthwhile.
Ways to Use the Set
- Rolling races on matched tracks to test whether mass affects rolling
- Dropping two balls together to show that falling does not depend on mass
- Head-on collisions between balls of equal and unequal mass
- Finding the coefficient of restitution from drop and rebound heights
Specifications
| Item | Set of three balls for mechanics experiments |
| Uses | Rolling, free fall, collisions and bounce tests |
| Properties students measure | Mass, diameter and density |
| Instruments needed | Balance, vernier calipers, metre rule |
| Materials, diameters and masses | Confirm at enquiry |
Care & Handling
- Keep the balls in a tray or box with separate compartments so they do not roll off benches or chip one another.
- Dry any metal ball after handling so fingerprints do not leave rust spots.
- Bounce tests should be done on a hard, clean floor area kept clear of people.
- Check the surfaces for chips or flats, which spoil rolling and collision results.
Why Choose LabEquip
Mechanics teachers want a small set of balls that serves many practicals, and three contrasting balls cover rolling, falling and collision work. LabEquip lists this set in its physics lab equipment range, where it pairs well with the Meca Ball identical tracks and the ball for free fall. The contact page is the place to confirm materials and sizes.
Frequently Asked Questions
Why do balls of different mass fall together?
A heavier ball has a larger weight but also a larger mass to accelerate, and the ratio of the two is the same g for every ball. Air resistance is the only thing that separates them, and for small dense balls it is very small.
How can the balls be used to find the coefficient of restitution?
Drop a ball from a measured height onto a hard floor and measure the height of the first bounce. The coefficient of restitution is the square root of the rebound height divided by the drop height.
How can the density of each ball be found?
Weigh the ball, measure its diameter with vernier calipers and calculate the volume as πd³/6. Density is mass divided by volume, which can be compared with tables to identify the material.
What happens when a moving ball hits a stationary ball of equal mass?
In a nearly elastic head-on collision the moving ball almost stops and the other moves off with nearly the same speed. Momentum passes from one ball to the other.
What if the moving ball is lighter than the one it hits?
It bounces back while the heavier ball moves forward slowly. Momentum is still conserved, because the rebound counts as negative momentum.
How should the balls be stored?
In a box or tray with separate spaces, kept dry. Loose balls roll off benches, chip each other and are soon lost, leaving the set incomplete.
Last Updated: October 2026










Reviews
There are no reviews yet.