Search

In Stock

Rectifier Diode

Diode de redressement 1N4007 Engineered for a peak repetitive reverse voltage (VRRM) of 1000V and an average forward current (IF) of 1.0A, utilizing a diffused junction architecture to ensure stable AC-to-DC rectification.

Low Leakage Thermal Design Housed in a standardized, flame-retardant DO-41 package with high thermal conductivity leads, facilitating minimal reverse current leakage (IR < 5.0\mu A) and robust performance under varying atmospheric laboratory conditions.

$1.80

Quick Answer: The Rectifier Diode is a silicon semiconductor component that lets current pass easily in one direction and blocks it in the other. A rectifier diode is used in physics and electronics practicals to plot a diode characteristic, to change alternating current into one-direction current and to protect circuits from a reversed supply.

A One-Way Valve for Current

Inside the body is a p-n junction. With the anode made positive relative to the cathode (forward bias), the junction barrier is overcome and the current rises rapidly once a small forward voltage is reached. With the polarity reversed, only a tiny leakage current flows until the reverse voltage exceeds the diode’s rating. The band printed round one end of the body marks the cathode, the end the current leaves by when the diode conducts.

Rectifier types are built for the currents and reverse voltages found in power circuits rather than for speed. That makes them right for mains-frequency rectification and protection work but less suited to very fast signals, where small-signal or fast-recovery diodes are used instead.

Plotting the Characteristic

The standard practical places the diode in series with a protective resistor and a variable supply, with a voltmeter across the diode and an ammeter in series. Students raise the voltage in small steps in the forward direction and note the current, then turn the diode round and repeat. The graph shows almost no current up to the knee, then a steep climb, and next to nothing in reverse, a clear contrast with the straight line of an ohmic resistor and a natural introduction to non-linear components.

Where It Is Used

  • Plotting forward and reverse current-voltage characteristics
  • Half-wave rectification, viewed on an oscilloscope with a resistor load
  • Protecting a circuit against a battery connected the wrong way round
  • Flyback protection across a relay coil or 12V DC motor to absorb the spike at switch-off
  • Building a full-wave rectifier from four diodes before moving to a ready-made diode bridge

Specifications

Component Silicon diode for rectification
Construction P-n junction; cathode marked by a band
Function Conducts in forward bias, blocks in reverse
Typical uses Rectification, reverse-polarity and flyback protection
Current and reverse-voltage rating Confirm at enquiry

Care & Handling

  • Always include a series resistor when plotting the diode’s characteristic; without one the forward current rises too fast and the diode overheats.
  • Bend the leads a short distance away from the body rather than right at it, to avoid cracking the seal.
  • Solder quickly and let each joint cool, since prolonged heat can damage the junction.
  • Keep diodes in labelled compartments so rectifier and signal types are not mixed up.

Why Choose LabEquip

Electronics teachers usually order these diodes in quantity, because they appear in many practicals and the odd one is lost to a missing resistor. LabEquip supplies them within our physics lab equipment range together with bridges and capacitors; send the quantity and rating you need through the contact page.

Frequently Asked Questions

Which end of the diode is the cathode?

The end marked with a printed band. In forward bias the anode goes to the positive side, and current enters at the anode and leaves at the cathode. The circuit symbol shows the same thing: its bar corresponds to the band on the body.

Why does the diode need a series resistor when I plot its characteristic?

Beyond the forward voltage, the current through a diode increases very steeply for a tiny rise in voltage. Without a resistor to limit it, the current can exceed the rating in a moment. The resistor makes the current change gradually so that readings can be taken safely.

What is the difference between a rectifier diode and a signal diode?

A rectifier diode is built to carry larger currents and withstand higher reverse voltages at mains frequency. A signal diode is smaller and switches faster but carries little current. Use a rectifier type for supplies and protection, and a signal type for detectors and fast switching.

Why is a diode placed across a motor or relay coil?

When the current in a coil is switched off, its collapsing magnetic field induces a large voltage that can damage switches and transistors. A diode connected in reverse across the coil gives that current a safe path to die away, so the spike is clamped.

Does a diode obey Ohm’s law?

No. Its current is not proportional to the voltage across it, and its resistance depends on both the voltage and the direction. That is why the diode characteristic is a curve with a knee and why the diode is the standard example of a non-ohmic component.

How can I test whether a diode is still working?

Use a multimeter on its diode-test setting. One way round it should show a forward-voltage reading; reversed it should show an open circuit. Near zero in both directions means the diode has failed short, and open circuit both ways means it has failed open.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
USD United States (US) dollar
Product has been added to your cart
Compare (0)