Quick Answer: The scanning tunneling microscope (STM) experiment teaches how an STM images conducting surfaces at the scale of individual atoms. A sharp metal tip is brought so close to the sample that electrons tunnel across the gap, and the tunnelling current is used to map the surface as the tip scans.
Quantum Tunnelling as a Measuring Tool
Classically, an electron cannot cross the gap between two conductors unless it has enough energy to escape the metal. In quantum mechanics it has a small probability of tunnelling through that barrier, and the probability falls exponentially with the gap width. When a small bias voltage is applied between a tip and a sample less than a nanometre apart, a tiny tunnelling current flows, and changing the gap by roughly the diameter of an atom changes that current by about an order of magnitude.
That extreme sensitivity is the whole principle of the STM. Piezoelectric actuators move the tip in steps far smaller than an atom, and a feedback loop adjusts the tip height to keep the current constant as it scans. The record of those height adjustments becomes the image of the surface.
Practical Work in the Experiment
Teaching STMs typically work in air, imaging surfaces that stay clean, such as freshly cleaved graphite, where the hexagonal pattern of carbon atoms can be resolved, and gold films, which show atomically flat terraces separated by single-atom steps. Students commonly prepare their own tips by cutting a fine platinum-iridium wire at an angle, which leaves a point sharp enough at the atomic scale often enough to be practical.
Beyond imaging, the experiment can cover constant-current and constant-height modes, current-distance curves that show the exponential dependence directly, and the effect of vibration and thermal drift on the image. The samples, tip material and software that come with this set should be confirmed at enquiry, since they define which applications can be explored.
Specifications
| Experiment | Principles and applications of scanning tunnelling microscopy |
| Physical principle | Quantum tunnelling current between a sharp tip and a conducting sample |
| Typical samples | Graphite and gold surfaces in air |
| Imaging modes | Constant current and constant height |
| Scan head, samples, tips and software supplied | Confirm at enquiry |
Applications in the Course
- Advanced undergraduate practicals in quantum and solid-state physics
- Imaging atomic lattices and surface steps on conducting samples
- Measuring the exponential dependence of tunnelling current on distance
- Introducing nanotechnology and surface science
Care & Handling
- Place the instrument on a vibration-damped surface away from doors, pumps and foot traffic
- Handle tips only with tweezers and never touch the tip end, which blunts instantly
- Approach the sample using the automatic or slow approach routine so the tip does not crash
- Keep samples covered when not in use, and cleave graphite again for a fresh surface when images degrade
Why Choose LabEquip
Universities and colleges adding nanoscience to their physics or materials courses use the STM experiment so that students reach atomic resolution themselves. LabEquip can advise on how it fits with other modern physics practicals such as the Hall effect in germanium; contact LabEquip to confirm the configuration.
Frequently Asked Questions
How can an STM resolve individual atoms?
The tunnelling current changes by about a factor of ten when the gap changes by roughly one atomic diameter. Because the current comes mainly from the atom at the very end of the tip, the microscope senses height differences far smaller than an atom.
Can the STM image any sample?
No. The sample must conduct electricity so that a tunnelling current can flow. Insulating samples need a different instrument, such as an atomic force microscope.
Why are graphite and gold used as samples?
Freshly cleaved graphite and gold films stay clean in air long enough to image. Graphite shows its atomic lattice, while gold shows flat terraces and single-atom steps.
How are the tips made?
Commonly by cutting a fine platinum-iridium wire at a steep angle with sharp cutters. This leaves a point that is often sharp enough at the atomic scale; a poor tip is simply cut again.
What is the difference between constant-current and constant-height mode?
In constant-current mode a feedback loop moves the tip up and down to hold the current steady, and the height record forms the image. In constant-height mode the tip stays level and the current changes are recorded, which is faster but only works on very flat areas.
Why is vibration such a problem?
The tip-sample gap is less than a nanometre, so building vibrations or footsteps can change it as much as the surface features do. A damped base and a quiet location are essential for clear images.
Last Updated: October 2026










Reviews
There are no reviews yet.