Quick Answer: The Capillary Tube Clamp is a holder that grips a fine glass capillary tube vertically so that its lower end dips into a liquid, for the capillary rise method of measuring surface tension. The clamp keeps the tube upright and still while the height of the liquid column is measured.
Holding the Tube for Capillary Rise
In the capillary rise method a clean glass tube of narrow bore is dipped vertically into water. Surface tension pulls the liquid up the tube until the weight of the raised column balances the upward pull at the meniscus. The height h gives the surface tension T through T = r h ρ g / (2 cos θ), where r is the bore radius, ρ the liquid density and θ the contact angle, which is close to zero for clean water on clean glass.
The formula assumes a vertical tube and an undisturbed meniscus, which is why the holder matters. The clamp grips the thin tube without crushing it and holds it upright above the beaker, usually from a stand rod through a square boss head or similar fitting. In the usual procedure a needle is clamped beside the tube with its tip just touching the water surface, and a travelling microscope reads first the meniscus and then the needle tip.
This item is the simple holder; for a set-up that also raises the beaker, see the rising table with capillary tube clamp. The jaw size, material and mounting of this clamp are not stated in the listing title.
Experiments
- Determining the surface tension of water by capillary rise
- Studying how detergent or temperature changes the height of rise
- Comparing tubes of different bore to show that height varies inversely with radius (Jurin’s law)
- Demonstrating capillarity to junior classes with coloured water
Specifications
| Item | Capillary tube clamp |
| Holds | Glass capillary tube, vertically |
| Mounting | On a laboratory stand rod |
| Used with | Beaker of liquid, reference needle, travelling microscope |
| Jaw size and material | Confirm at enquiry |
Care & Handling
- Tighten the clamp only enough to hold the tube; thin capillaries crack easily.
- Clean tubes with detergent or dilute alkali, rinse with distilled water and avoid touching the lower end.
- Check that the tube is vertical with a set square or plumb line before reading.
- Keep the clamp dry and its screw lightly oiled.
Why Choose LabEquip
Physics teachers buy capillary tube clamps for the surface tension practical, often several per class so that every group can work at once. LabEquip lists this clamp in Physics Equipments, and our contact page can help match it to your stands.
Frequently Asked Questions
Why must the capillary tube be vertical?
The rise is set by vertical height, and a tilted tube makes that height harder to read with a travelling microscope while the meniscus becomes lopsided. Clamping the tube truly vertical keeps the measurement simple and the formula valid.
How is the bore of the capillary measured?
After the experiment, cut the tube at the position of the meniscus and measure the internal diameter in two perpendicular directions with a travelling microscope. Half the average diameter is the radius used in the formula.
Why does dirty glass give a low result?
Grease raises the contact angle between water and glass, so the meniscus is less curved and the liquid rises less. Clean the tube with detergent or dilute alkali, rinse with distilled water and do not touch the lower end.
How does tube bore affect capillary rise?
The height of rise is inversely proportional to the bore radius, which is Jurin’s law. A tube of half the radius raises the liquid about twice as high, a result students can check with tubes of different bores.
What is the difference between this clamp and the rising table with capillary tube clamp?
This item holds the tube alone and fixes to an existing stand. The rising table combines a clamp with a height-adjustable platform for the beaker, so the liquid can be raised to the needle without disturbing the tube.
How tight should the clamp be?
Just tight enough that the tube does not slide down under its own weight. Glass capillary tubes are thin-walled and crack easily, so a strip of paper wrapped round the tube under the jaws gives extra protection.
Last Updated: October 2026










Reviews
There are no reviews yet.