Search

In Stock

Capillarity Study Device

Appareil d'étude de la capillarité, High-Clarity Borosilicate Glass Observation du phénomène de capillarité, enables the technical evaluation of meniscus curvature and surface tension coefficients across varied liquid densities in undergraduate chemistry trials.

Integrated Stabilization Reservoir supports the Application of evidentiary-grade measurement protocols, ensuring repeatable data acquisition and minimizing experimental variance during high-cadence laboratory rotations.

₹4,560.00

Quick Answer: A capillarity study device holds several glass capillary tubes of different internal bores so that they dip into the same liquid side by side. The capillarity study device shows that a wetting liquid rises higher in narrower tubes and lets students test Jurin’s law quantitatively.

Jurin’s Law in Numbers

In a capillary tube of radius r, a liquid that wets glass climbs until the upward pull of surface tension around the rim, 2πrγcosθ, balances the weight of the raised column, πr²hρg. Rearranging gives Jurin’s law, h = 2γcosθ/(ρgr): the height is inversely proportional to the radius. For clean water in glass the contact angle θ is close to zero, so cosθ ≈ 1.

As a guide to what to expect, water should rise about 30 mm in a tube of 0.5 mm radius and about 15 mm in a tube of 1 mm radius. Doubling the bore halves the rise, and that ratio is what students check first on the capillarity study device.

From Heights to Surface Tension

A graph of h against 1/r should be a straight line through the origin with gradient 2γ/(ρg). Multiplying the gradient by ρg/2 gives the surface tension of the liquid; for water the result should come out near 0.07 N/m at room temperature.

The radius of each tube matters as much as the height. If the bores are not marked, a travelling microscope sighted on the cut end gives the internal diameter. Heights are measured from the flat liquid surface outside the tubes to the bottom of each meniscus.

Specifications

Product Capillary action apparatus with tubes of different bores
Law tested Jurin’s law, h = 2γcosθ/(ρgr)
Measured quantities Capillary rise in each tube, tube radius
Typical liquid Clean water, lightly coloured for visibility
Number of tubes, bores and holder Confirm at enquiry

Care & Handling

  • Clean the tubes with detergent solution, then rinse many times with distilled water
  • Never blow into or push wire through the tubes; the bores are easily blocked or chipped
  • Let the tubes drain and dry standing upright, covered from dust
  • Handle the glass tubes gently and check the open ends for chips before use

Practical Work

  • Showing that narrower tubes give higher capillary rise
  • Plotting rise against 1/radius to test Jurin’s law
  • Estimating the surface tension of water from the graph gradient
  • Comparing water with ethanol or soap solution

Why Choose LabEquip

Secondary schools and colleges buy a capillarity study device to turn a familiar observation into a graph and a value for surface tension. LabEquip also supplies the wedge-shaped capillary vessel, which shows the same law as a continuous curve, and other physics lab equipment; ask LabEquip for class sets.

Frequently Asked Questions

What does Jurin’s law predict?

That the height a liquid rises in a capillary tube is inversely proportional to the tube’s radius. A tube half as wide gives twice the rise, provided the liquid and the glass are the same.

How can surface tension be estimated from the readings?

Plot rise against one over the radius. The gradient equals 2γ/(ρg) for a fully wetting liquid, so the surface tension is the gradient multiplied by ρg and divided by two.

Why wet the tube walls before taking a reading?

A dry tube resists the advancing liquid, so the column can stop short. Dip the tubes deeper or tilt them so the liquid climbs past its final level, then return them, so each meniscus falls back to its equilibrium height on a wetted wall.

Where should the height be measured from?

From the flat surface of the liquid outside the tubes, not from the dish bottom, up to the lowest point of the curved meniscus inside the tube.

Why might two tubes of the same bore give different heights?

A trace of grease or dust in one tube, a bore that is not uniform along its length, or a dry wall where the meniscus stopped early. Cleaning and re-wetting both tubes usually brings them into line.

Are the tube bores supplied with the device?

The number of tubes and their bores can be confirmed at enquiry. If the radii are not marked, they can be measured with a travelling microscope on the cut end of each tube.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
INR Indian rupee
Product has been added to your cart
Compare (0)