Search

In Stock

Battery 9V

Accumulateur 9 V, Linear Discharge Curve supports the technical Analysis of Ohm’s Law and circuit stability, ensuring consistent voltage during high-cadence undergraduate electronics trials.

Standardized PP3 Interface Rechargeable 9 V, enables the immediate Application of portable instrumentation, including multimeters and signal generators, reinforcing practical troubleshooting skills in Vocational training.

Impact-Resistant Technical Casing Technology NiMH maintains experimental Consistency across high-cadence laboratory rotations by protecting internal electrochemical cells from mechanical failure.

$10.04

Quick Answer: This 9V rechargeable battery is a rectangular PP3-format block with snap terminals, supplied as an accumulator that can be recharged rather than thrown away. Laboratories use a 9V rechargeable battery in multimeters, sensors, timers and small electronic circuits that are used often enough for repeated recharging to make sense.

Why a Rechargeable 9 V Block Reads Below 9 V

A 9 V block is several small cells connected in series inside one case. In a rechargeable nickel-metal hydride (NiMH) block each cell gives about 1.2 V, so a pack of seven cells has a nominal voltage of about 8.4 V, and some designs use eight cells for about 9.6 V. Lithium-based 9 V blocks use different internal arrangements. Most equipment designed for 9 V works happily at these voltages, but a meter’s low-battery warning may appear a little earlier than with a fresh disposable battery.

This is a useful talking point in electricity lessons: the label states a nominal value, while the actual terminal voltage depends on the cell chemistry, the state of charge and the current being drawn.

Charging, Self-Discharge and Energy Stored

A rechargeable block must be charged in a charger made for its chemistry; a NiMH charger and a lithium charger work in different ways, and disposable alkaline blocks must never be put in any charger. Rechargeable cells also lose charge slowly while standing. A meter that sits in a drawer for a term may find its battery partly flat, so charge blocks before the lessons in which they are needed.

The energy stored can be estimated from the capacity printed on the block. A block rated at 200 mAh and 8.4 V, for example, stores about 0.2 A × 3600 s × 8.4 V ≈ 6 kJ, a figure students can compare with the energy needed to run a circuit for a known time.

Specifications

Format 9 V rectangular block (PP3 size) with snap terminals
Type Rechargeable block (accumulator)
Charging Charger designed for 9 V blocks of the same chemistry
Typical loads Multimeters, sensors, timers, small electronic circuits
Chemistry, capacity and nominal voltage Confirm at enquiry

Applications

  • Powering multimeters and handheld meters used every week
  • Running sensors, timers and small electronic projects in practical classes
  • Comparing nominal and measured terminal voltages in electricity lessons
  • Estimating stored energy from capacity and voltage

Care & Handling

  • Never carry or store 9 V blocks loose with keys, coins or other batteries; the two terminals sit close together and are easily short-circuited, which can make the block hot.
  • Fit the terminal cap or tape over the terminals when the block is out of a device.
  • Remove the block from equipment that will not be used for some weeks.
  • Take worn-out blocks to a battery collection point rather than household waste.

Why Choose LabEquip

Schools that use meters and sensors every week often switch to rechargeable blocks to cut the number of disposable batteries they buy and throw away. LabEquip lists this block in its physics lab equipment range; for equipment used only occasionally, the alkaline 9 V battery holds its charge better on the shelf. Ask through the contact page about chemistry and capacity.

Frequently Asked Questions

Why does a rechargeable 9 V battery read below 9 V?

A NiMH 9 V block contains seven or eight cells of about 1.2 V each, giving a nominal 8.4 V or 9.6 V rather than exactly 9 V. Most devices designed for 9 V still work normally at these voltages.

Which charger should be used?

One designed for 9 V blocks of the same chemistry as the battery, NiMH or lithium. Never put a disposable alkaline 9 V battery into any charger, because it can leak or overheat.

Is a rechargeable block suitable for a meter that stays unused for weeks?

Rechargeable cells slowly lose charge while standing, so a block left in a drawer may be partly flat when needed. Charge it before use, or keep an alkaline block for rarely used equipment.

How much energy does a 9 V rechargeable block store?

Multiply the capacity in ampere-hours by 3600 and by the nominal voltage. A block rated at 200 mAh and 8.4 V would store about 6000 joules, which students can compare with the energy a circuit uses.

Why should 9 V batteries never be carried loose with keys or coins?

Both terminals are on the same end, close together, so a coin or key can bridge them and short-circuit the battery. The current that flows can make the block hot enough to cause burns or a fire.

When should a rechargeable block be replaced?

When it no longer holds a charge for a useful time or runs a meter for noticeably less time than when new. Take the old block to a battery recycling point.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
USD United States (US) dollar
Product has been added to your cart
Compare (0)