Search

In Stock

FIXED 2 OHM RESISTOR

Nominal resistance of 2 Ω with controlled tolerance, enabling reliable current and voltage analysis

Thermally stable resistive element, designed for consistent performance during repeated laboratory use

₹175.00

Quick Answer: The fixed 2 ohm resistor is a low-value resistor for school electricity practicals. Used in pairs or alongside other values, the 2 ohm resistor lets students build series and parallel combinations, predict the total resistance and check the prediction with an ammeter and voltmeter.

Combination Rules with Two-Ohm Resistors

In series, resistances add: two of these resistors make 4 ohms and three make 6 ohms, because the current must pass through each in turn. In parallel, the reciprocals add: two side by side make 1 ohm, since each branch carries part of the current for the same voltage. With identical values the arithmetic stays simple enough for students to concentrate on the physics rather than the calculation.

Measurement then checks the theory. With a cell, an ammeter and a voltmeter across the whole combination, the total resistance follows from V/I. Equal resistors in series each take an equal share of the voltage, which students confirm by moving the voltmeter from one to the next; in parallel each has the full voltage across it, while the ammeter shows the current dividing equally between the branches.

Power adds another layer. In series the same current flows through each resistor, so each dissipates I²R. Swapping one for a resistor of a different value shows that the larger resistance now takes the larger share of voltage and power, which is why a series string of unmatched lamps glows unevenly. Low values like two ohms draw substantial current from cells, so readings should be taken quickly with a key in the circuit.

Specifications

Component Fixed resistor
Nominal value 2 ohms, as titled
Two in series 4 ohms
Two in parallel 1 ohm
Power rating, tolerance and mounting Confirm at enquiry

Practicals

  • Verifying the series rule, R = R1 + R2 + R3
  • Verifying the parallel rule, 1/R = 1/R1 + 1/R2
  • Showing equal voltage sharing between equal resistors in series
  • Mixed series-parallel networks for problem-solving practicals
  • A low-value load for internal resistance and power-transfer experiments

Care & Handling

  • Use a tapping key so current flows only while the meters are read; low resistances draw large currents from cells.
  • If the resistor has warmed during a run, allow it to cool before the next reading, since its value shifts slightly with temperature.
  • Keep connecting leads short and tight, because lead resistance is a noticeable fraction of two ohms.
  • Label resistors clearly, as small resistors of different values can look alike.

Why Choose LabEquip

Teachers who put together their own electricity experiment kits for schools usually buy 2 ohm resistors in multiples, so that each group can build networks from matched values. The fixed 1 ohm resistor adds a second value for mixed networks, and 4mm banana plug connectors make leads for the meters; all are in LabEquip’s physics lab equipment. Request quantities on the contact page.

Frequently Asked Questions

What is the resistance of two 2 ohm resistors in parallel?

One ohm. For equal resistors in parallel, the total is one resistor’s value divided by the number of branches, so two give 1 ohm and four give half an ohm.

Why do equal resistors in series share the voltage equally?

The same current flows through each, and each has the same resistance, so V = IR gives each the same voltage. The voltages across all of them add up to the supply voltage.

How do I measure the resistance of a combination?

Connect a cell, a key and an ammeter in series with the combination, and a voltmeter across it. Close the key, read both meters and divide the voltage by the current. Compare the result with the value predicted by the rules.

Which resistor gets hotter in a series circuit of different values?

The larger one. The current is the same through both, so the power I²R is greater where the resistance is greater. In parallel the reverse happens: the smaller resistor carries more current and dissipates more power.

Why does adding resistors in parallel lower the total resistance?

Each new branch gives the current another path, so for the same supply voltage more total current flows. A larger current at the same voltage means a smaller total resistance.

Why should a key be used in the circuit?

With only a few ohms in the circuit, cells deliver large currents and run down quickly, and the resistor and leads warm up, changing the readings. A key lets current flow only for the few seconds needed to read the meters.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
INR Indian rupee
Product has been added to your cart
Compare (0)