Search

In Stock

FIXED 1 OHM RESISTOR

Nominal resistance of 1 Ω with low tolerance, ensuring accurate current and voltage calculations

High thermal stability construction, suitable for continuous laboratory experimentation

₹160.00

Quick Answer: The fixed 1 ohm resistor is a single-value resistor for physics electricity practicals. Because its resistance is one ohm, the voltage across the 1 ohm resistor in volts equals the current through it in amperes, which makes it handy for measuring current with a voltmeter and as a low-value load in internal resistance experiments.

What a One-Ohm Value Makes Possible

Ohm’s law, V = IR, becomes V = I when R is one ohm. Connect the resistor in series in a circuit and a voltmeter across it reads the current directly, so 0.25 V means 0.25 A. This is the principle of the current-sense resistor used in electronics, and it lets a class with more voltmeters than ammeters still measure current, or lets an oscilloscope display current as a voltage.

A low-value resistor is also the natural load for showing the internal resistance of a cell. A fresh dry cell connected to a high resistance gives a terminal voltage close to its emf, but connected across one ohm it drives a large current and its terminal voltage drops noticeably. The lost volts, emf minus terminal voltage, divided by the current give the internal resistance, r = (E − V)/I.

The same low value carries a caution. Even a single cell can drive close to an ampere through one ohm, and the power turned into heat is I²R. Circuits should include a switch or tapping key so that current flows only while readings are taken, and the resistor’s power rating should be respected, since a small resistor overheats quickly when overloaded.

Practicals

  • Measuring circuit current with a voltmeter, since V = I for a one-ohm resistor
  • Loading a cell to measure its terminal voltage and internal resistance
  • Building series and parallel networks with other fixed values
  • Displaying current waveforms on an oscilloscope as a voltage across the resistor
  • Comparing low-resistance measurements by the voltmeter-ammeter method and by a metre bridge

Care & Handling

  • Switch on the current only while taking readings; a cell connected across a low resistance runs down quickly and warms the resistor.
  • Let the resistor cool between readings when currents are large, since its value drifts slightly as it heats.
  • Tighten terminals firmly; at one ohm, a loose connection can add a resistance comparable to the resistor itself.
  • Keep resistors sorted and labelled by value so a 1 ohm part is not mistaken for a 10 ohm one.

Specifications

Component Fixed resistor
Nominal value 1 ohm, as titled
Key relation Voltage across it in volts equals current in amperes
Typical use Current sensing and low-value load in school circuits
Power rating, tolerance and mounting Confirm at enquiry

Why Choose LabEquip

Physics teachers order fixed 1 ohm resistors in sets for internal resistance and current-measurement practicals. The fixed 2 ohm resistor pairs with it for combination experiments, and both are listed in LabEquip’s physics lab equipment. Send quantities through the contact page.

Frequently Asked Questions

Why is a 1 ohm resistor useful for measuring current?

By Ohm’s law the voltage across it equals the current multiplied by one ohm, so a voltmeter reading in volts gives the current in amperes. This lets a voltmeter or oscilloscope stand in for an ammeter.

How is the internal resistance of a cell found with it?

Measure the cell’s voltage on open circuit, which is close to its emf, then connect the resistor and measure the terminal voltage and the current. The internal resistance equals the drop in voltage divided by the current.

Can a single cell overheat the resistor?

It can warm it noticeably. A fresh cell may drive close to an ampere through one ohm, and small resistors are made for limited power. Keep the circuit closed only for the moment needed to read the meters.

Why do connection resistances matter more at one ohm?

Leads, clips and terminals each add a small resistance, often a few hundredths of an ohm or more. Against one ohm that can be several percent, so short leads and tight connections are needed for accurate results.

Where are low-value resistors used outside the laboratory?

In chargers, power supplies and motor controllers, a low-value resistor in series lets the electronics measure current from the small voltage across it. It is the same principle students use in the practical.

How can students check the resistor’s value?

Pass a measured current through it and record the voltage across it at several currents. The gradient of the V against I graph gives the resistance. A multimeter on its lowest range gives a quick check, after subtracting the reading with the probes touching.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
INR Indian rupee
Product has been added to your cart
Compare (0)