Quick Answer: The fixed resistor 100 ohm is a single-value resistor for electricity and electronics practicals where currents should stay in the milliamp range. The 100 ohm resistor limits current from low-voltage supplies, forms voltage dividers with other resistors and, with a capacitor, sets the time constant of charging circuits.
Where a Hundred Ohms Fits in a Circuit
With 100 ohms in a circuit, a few volts drive only tens of milliamps: by Ohm’s law, a 3 V supply gives 30 mA. That keeps currents within the range of milliammeters and the ratings of components such as LEDs, buzzers and small transistors, and it keeps the power dissipated small. A resistor of this value is therefore a common current-limiting part in electronics projects and a safe choice for Ohm’s law practicals with milliammeters.
Two resistors in series across a supply share its voltage in proportion to their resistances, forming a voltage divider. Two equal resistors of this value halve the supply voltage. With a light-dependent resistor or a thermistor in place of one of them, the output voltage changes with light or temperature, which is the basis of many sensor circuits built in school electronics.
With a capacitor, the resistor sets how quickly the capacitor charges and discharges. The time constant is RC, the product of resistance and capacitance. With 100 ohms it is short unless the capacitor is large, so a data logger or oscilloscope is the usual way to record the charging curve; with 10,000 microfarads the time constant is one second.
Care & Handling
- Check the value with a multimeter before a precise practical, since the real resistance may differ from the marked value by its tolerance.
- Keep the supply voltage modest; even at small currents a resistor warms if its power rating is exceeded.
- Where wire leads are fitted, bend them gently and away from the body of the resistor to avoid cracking it.
- Store resistors by value in labelled compartments.
Specifications
| Component | Fixed resistor |
| Nominal value | 100 ohms, as titled |
| Current level | Milliamps with low-voltage supplies |
| Typical use | Current limiting, voltage dividers and RC timing |
| Power rating, tolerance and form | Confirm at enquiry |
Applications
- Limiting the current through an LED or buzzer in low-voltage circuits
- Ohm’s law practicals with a milliammeter and voltmeter
- Building voltage dividers, including sensor circuits with an LDR or thermistor
- Recording the charging and discharging of a capacitor through a known resistance
- Practising colour codes and resistance measurement with a multimeter
Why Choose LabEquip
Schools and colleges stock 100 ohm resistors for electronics projects, sensor circuits and Ohm’s law practicals with milliammeters. For larger, ammeter-scale currents the fixed 5 ohm resistor is the usual choice, and both are in LabEquip’s physics lab equipment. Ask about forms and quantities through the contact page.
Frequently Asked Questions
What colour bands does a 100 ohm resistor have?
On colour-coded resistors, 100 ohms is brown, black, brown: 1, 0 and a multiplier of ten. A further band, often gold or silver, gives the tolerance. Mounted laboratory resistors may simply be labelled with the value instead.
Why use a 100 ohm resistor with an LED?
Once an LED conducts, its current rises steeply with voltage, so without a series resistor it can draw enough current to fail. The resistor limits the current to a safe level, found from the supply voltage minus the LED’s forward voltage, divided by the resistance.
What current flows through it from a 6 V supply?
By Ohm’s law, 6 V divided by 100 ohms gives 0.06 A, or 60 mA, ignoring the supply’s internal resistance. The power dissipated is then 0.36 W, so the resistor’s power rating must be higher than that.
How does a voltage divider with two equal resistors work?
The supply voltage is shared in proportion to the resistances, so two equal resistors take half each. Replacing one with a different value changes the share, and the output is taken across the lower resistor.
How is the time constant of an RC circuit calculated?
Multiply the resistance in ohms by the capacitance in farads. With 100 ohms and 10,000 microfarads, RC is one second, the time for a charging capacitor to reach about 63 percent of the supply voltage.
How accurate is the marked value?
Every resistor has a tolerance, the percentage by which its real value may differ from the marked one. Measuring it with a multimeter, or from a V against I graph, gives the actual value to use in calculations.
Last Updated: October 2026










Reviews
There are no reviews yet.