Search

In Stock

LAMP 1.5V

Rated operating voltage of 1.5 volts DC, compatible with standard dry cells and lab power sources

Fine tungsten filament with controlled resistance, ensuring predictable illumination characteristics

$2.09

Quick Answer: The 1.5V lamp is a miniature filament lamp rated for 1.5 volts, the voltage of a single dry cell. Teachers use the 1.5V lamp to show that a complete circuit is needed for current to flow, to test which materials conduct and to compare how series and parallel connections affect brightness on one cell.

Matching a Lamp to One Cell

A filament lamp glows brightest and lasts longest at the voltage it was made for. A lamp rated at 1.5 V matches one cell, so the simplest circuit of all, one cell, one lamp and two wires, lights it properly. That makes it ideal for first lessons on circuits, where pupils discover that the lamp lights only when there is an unbroken path from one terminal of the cell, through the filament and back to the other.

Connected to two or three cells, the same lamp is overrun. It glows brighter and whiter for a while, but the filament runs much hotter and usually fails soon after, which is a useful warning about matching components to supplies. For two-cell circuits a lamp rated at 3 V is the right partner.

Inside the glass the filament is a fine coil of tungsten. Current heats it until it glows, so the lamp is a direct demonstration of the heating and lighting effects of an electric current. Pupils can feel the glass warm after a few minutes, which leads naturally to a discussion of how much of the energy becomes light and how much becomes heat.

Specifications

Component Miniature filament lamp
Rated voltage 1.5 V, as titled, matching one cell
Effects shown Heating and lighting effects of a current
Used with Miniature lamp holders on circuit boards and in kits
Base type, current rating and pack quantity Confirm at enquiry

Classroom Uses

  • First circuits with one cell, a lamp, a switch and connecting wires
  • Testing materials as conductors or insulators in a simple circuit tester
  • Comparing two lamps in series with two lamps in parallel on a single cell
  • Showing the heating and lighting effects of an electric current
  • Building models such as torches, lighthouses or room lighting in project work

Care & Handling

  • Run the 1.5V lamp from a single cell; more cells overheat the filament and shorten its life.
  • Hold the lamp by its base rather than the glass, and let it cool for a few seconds before removing it from its holder.
  • Store spare lamps in a padded box, since the fine filament breaks if a lamp is dropped.
  • If a lamp does not light, test the cell and the holder contacts before assuming the filament has failed.

Why Choose LabEquip

Primary and middle school teachers stock these lamps in quantity for circuit-building lessons, where breakages and overrun bulbs are part of learning. For two-cell circuits use the 3V bulb, and see LabEquip’s physics lab equipment for holders and boards. Request pack quantities on the contact page.

Frequently Asked Questions

Why does the lamp blow when used with two cells?

Two cells supply about twice the voltage the lamp is made for, so a much larger current flows and the filament runs far hotter. It glows brightly for a short time and then the tungsten coil melts or breaks.

Why are two lamps in series dimmer than one?

In series the cell’s voltage is shared between the two filaments, so each gets about half and carries a smaller current. In parallel each lamp gets the full cell voltage and glows normally, although the cell runs down faster.

How can the lamp be used to test conductors?

Make a circuit of a cell, the lamp and two wires with a gap between their free ends. Touch the ends to a material: if the lamp lights, the material conducts. Weak conductors may give a dim glow or none at all.

Why does a lamp sometimes flicker in a pupil’s circuit?

Flickering usually means a loose connection, a lamp not seated firmly in its holder or a crocodile clip slipping on a terminal. Press each connection in turn while the circuit is on to find the faulty one.

Is the lamp safe for young pupils?

At 1.5 volts there is no shock risk, but the glass can break and the bulb becomes warm after a few minutes. Pupils should not join the cell terminals directly with bare wire, which makes the wire hot.

What does the lamp show about energy?

Electrical energy from the cell is transferred to the filament, which heats up and gives out light. Most of the energy leaves as heat rather than light, which is why filament lamps have largely been replaced by LEDs for household lighting.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
USD United States (US) dollar
Product has been added to your cart
Compare (0)