Quick Answer: A complete 1.2 m mechanics bench is a straight, graduated track along which a wheeled trolley runs, supplied as a set with the parts needed for motion practicals. The 1.2 m mechanics bench is used to study uniform and accelerated motion, forces, momentum and energy with trolleys rather than gliders.
Compensating for Friction Before Measuring
Wheeled trolleys on the 1.2 m mechanics bench lose a little speed to rolling friction and axle friction. The standard remedy is to raise the end of the track very slightly, until a trolley given a gentle push rolls down at a constant speed. At that angle the component of the trolley’s weight along the slope just balances friction, so any pulling force added afterwards is the net force on the trolley.
Students can check the setting by timing the trolley over two equal halves of the track: equal times mean constant speed. Once compensated, a thread over the end pulley to a hanging mass gives an acceleration that can be compared with a = F/m.
Recording Motion with Video
Because the track is graduated, a phone or camera placed square to the bench records the trolley’s position against the scale in every frame. Stepping through the clip frame by frame gives position at equal time intervals, from which velocity and acceleration follow. Keeping the camera level with the track and at a distance reduces parallax at the ends of the run.
Video also suits collision and explosion work. When two trolleys pushed apart by a spring plunger fly off in opposite directions, the distances they cover in the same time are in the inverse ratio of their masses, a direct check of momentum conservation.
Practicals on the Bench
- Acceleration against force on a friction-compensated track
- Trolley explosions and collisions to test conservation of momentum
- Gravitational potential energy converted to kinetic energy on an inclined track
- Video analysis of position against time using the graduated scale
- Comparing rolling trolleys with the near-frictionless gliders of an air track
Specifications
| Product | Mechanics bench, supplied as a complete set |
| Track length | 1.2 m, as titled |
| Moving body | Wheeled trolley running on the track |
| Track marking | Graduated, for reading positions directly or on video |
| Measurements | Displacement, velocity, acceleration, momentum, energy |
| Exact contents of the set | Confirm at enquiry |
Care & Handling
- Keep the running surface free of grit, which causes jumps in the trolley’s speed
- Use the end stops so trolleys cannot run off the bench onto the floor
- Check that the trolley wheels spin freely and wipe hair or fluff from the axles
- Store the track flat or fully supported so the 1.2 m length stays straight
Why Choose LabEquip
Schools and colleges that want one bench to cover the whole mechanics sequence, from uniform motion to momentum, choose a complete 1.2 m mechanics bench because the parts are matched. LabEquip can add the stepped pulley accessory for torque work and supply further physics lab equipment for the same lab; ask LabEquip for the set list and quantities.
Frequently Asked Questions
How is friction compensated on a trolley track?
Raise the end of the track a little at a time until a trolley given a small push rolls at a steady speed. The slope then cancels friction, so the force from a hanging mass becomes the resultant force on the trolley.
What does a trolley explosion show?
Two trolleys at rest are pushed apart by a released spring. Total momentum starts at zero and stays zero, so the lighter trolley moves faster. With masses in a 2 to 1 ratio, the lighter one travels twice as far in the same time.
How can a phone video replace light gates?
Film the run square to the graduated track at a known frame rate, then read the trolley’s position on the scale in successive frames. The frame interval is the time step, so velocity and acceleration follow from the position readings.
Why is the track graduated?
The scale lets positions be read directly, by eye or on video, without a separate metre rule. It also makes it easy to place light gates or start points at measured distances.
Can the bench be used on a slope for energy experiments?
Yes. Raise one end to a measured height, release the trolley and measure its speed at the bottom. Comparing mgh with ½mv² shows how much energy goes to friction and to spinning the wheels.
What comes in the complete set?
The exact contents of this complete set can be confirmed at enquiry. A practical set normally includes the track, at least one trolley, an end pulley and hanging masses so that force and motion work can start straight away.
Last Updated: October 2026










Reviews
There are no reviews yet.