Quick Answer: The 3-way valve is a tap with three ports and a turning handle that sets which ports are joined together. In physics and chemistry set-ups the 3-way valve switches a gauge, syringe or pump between lines, isolates part of a circuit or vents it to the air.
How the Bore Decides the Route
Inside the valve a rotating plug carries a drilled passage. With an L-shaped bore, the passage links two neighbouring ports and blocks the third, and a quarter turn of the handle selects a different pair. With a T-shaped bore, one position joins all three ports at once and other positions join two of them. Many valves show the bore with a line or arrow moulded on the handle; if not, turning the handle and blowing gently through each port reveals the route.
Knowing the bore type matters in pressure work. An L-bore can isolate a gauge completely, whereas a T-bore, in its all-ports position, cannot. The bore type, body material and port size of this listing are confirmed at enquiry.
Typical Uses in Pressure Experiments
In a Boyle’s law experiment the valve sits between a syringe, a pressure gauge or sensor and the open air. With the third port open, the syringe is set to its starting volume at atmospheric pressure; one turn then seals syringe and gauge together, so the initial conditions are known exactly. Between runs the valve vents the circuit back to zero without pulling any tubing off.
In fluids work a single gauge can be switched between two tapping points, for example the inlet and the throat of a Venturi tube, to compare their pressures. The same valve lets a hand pump fill a bottle while a gauge watches the pressure, then closes the line so the pump can be removed.
Specifications
| Product | Three-port valve (stopcock) for tubing circuits |
| Ports | Three, selected by turning the handle |
| Function | Routing, isolating and venting gas or liquid lines |
| Common bore patterns | L-bore (two ports at a time) or T-bore (can join all three) |
| Bore type, material and port size | Confirm at enquiry |
Where It Is Used
- Setting the starting volume of a syringe before a gas-law run
- Venting a gauge or pressure sensor to atmosphere between readings
- Switching one gauge between two tapping points on a flow apparatus
- Isolating a pressurised bottle from the pump that filled it
Care & Handling
- Turn the handle only when the circuit is at a safe pressure
- Push tubing fully onto the ports and add a small clip if the line will be pressurised
- Flush out water after use and let the valve dry with the handle part-open
- Keep solvents away unless the valve material is known to resist them
Why Choose LabEquip
Teachers who build pressure and gas-law circuits from separate parts find a 3-way valve saves dismantling tubing between every run. It pairs naturally with the needle pressure gauge; contact LabEquip to confirm port sizes before ordering, or browse more physics lab equipment.
Frequently Asked Questions
What is the difference between an L-bore and a T-bore 3-way valve?
An L-bore joins two of the three ports at a time and closes the third. A T-bore can also connect all three together, which helps with filling and venting but means a gauge cannot be fully isolated in that position.
How can I tell which ports are connected?
Many valves mark the bore with a line or arrow on the handle. If yours does not, turn the handle and blow gently through each port in turn with a clean tube, noting where the air comes out.
Why put the valve into a Boyle’s law experiment?
It lets the syringe be filled at atmospheric pressure with the third port open, then sealed to the pressure gauge or sensor by a single turn, so the starting volume and pressure are known exactly.
Can the valve be used with liquids?
Many valves of this type handle both gases and water, but the body and seal materials decide that. Flush water out after use and avoid solvents unless the valve material is known to resist them.
Should the valve be greased?
Stopcocks with a tapered glass or plastic plug need a thin film of suitable grease to seal and turn smoothly; valves with built-in seals generally do not. Never use a grease that could react with what flows through the line.
Which tube sizes fit the valve?
The port size depends on the model and can be confirmed at enquiry. Choose tubing that is a firm push fit, and secure it with a small clip if the circuit will be pressurised.
Last Updated: October 2026










Reviews
There are no reviews yet.