Quick Answer: The Ticker Tape Timer is a motion recorder that prints dots at a steady rate on a paper tape pulled through it by a moving object, so the spacing between dots shows how far the object moved in each equal interval of time. Schools use the ticker tape timer to measure speed, acceleration and the acceleration of free fall.
Reading Motion from a Strip of Tape
Inside the timer a vibrating arm strikes the tape through a disc of carbon paper, leaving a dot at each stroke. The object being studied, often a trolley or a falling mass, is attached to the end of the tape and drags it through the timer. A long gap between dots means high speed and bunched dots mean slow motion. Since the striking rate is steady, the tape becomes a record of position against time drawn by the motion itself.
Timers are built in more than one way, and LabEquip also lists a ticker tape timer, AC type, whose dot rate follows the supply frequency. Whatever the drive, the interval of a particular timer can be checked by running tape through it for a measured time and counting the dots, and that calibrated interval is then used in every calculation.
A favourite use is measuring g. With the timer clamped vertically at the edge of a high bench, a mass taped to a length of tape is dropped and the dots record its fall. The gaps between successive dots grow by an equal amount each interval, and that constant increase divided by the square of the interval gives the acceleration. Results usually come out somewhat below the accepted value because the tape rubs in the guides and the striker drags on it at each dot.
Specifications
| Function | Prints dots on paper tape at a regular interval |
| Marking | Vibrating striker acting through a carbon paper disc |
| Quantities obtained | Displacement, velocity and acceleration from dot spacing |
| Calibration | Count dots over a timed run to confirm the interval |
| Drive type and operating supply | Confirm at enquiry |
Practicals with a Ticker Timer
- Measuring the acceleration due to gravity with a falling mass pulling the tape
- Recording a trolley pulled by a constant force to test Newton’s second law
- Building tape charts by cutting the tape into equal-interval strips and pasting them side by side
- Comparing velocities before and after a collision between two trolleys
- Showing that a trolley on a friction-compensated runway moves at constant speed
Care & Handling
- Run the ticker tape timer only from the supply marked on it, through a laboratory power unit, and switch it off between runs so the striker does not wear through the carbon disc.
- Thread the tape under the carbon disc and keep its path straight so it does not snag in the guides.
- Replace the carbon disc when the dots become faint, turning it slightly between runs to spread the wear.
- Clamp the timer firmly to the bench or a stand so it does not shift as the tape is pulled.
Why Choose LabEquip
Secondary schools buy ticker timers in sets so that several groups can record motion at the same time, usually with trolleys, runways and rolls of tape. This timer is part of LabEquip’s physics lab equipment range; ask about tape, carbon discs and power arrangements through the contact page.
Frequently Asked Questions
Can the timer measure g?
Yes. Clamp the timer vertically, attach a mass to the tape and let it fall. The increase in the gap between consecutive dots is constant, and dividing that increase by the square of the dot interval gives the acceleration of free fall.
Why does the free-fall result come out below 9.8 m/s²?
The tape is slowed by friction in the guides and by the striker pressing on it at each dot. These forces act against the fall, so the measured acceleration is lower. A heavier falling mass reduces the effect, because friction becomes a smaller share of its weight.
What is a tape chart?
A tape chart is made by cutting the tape into strips that each contain the same number of dot intervals and gluing them side by side in order. Each strip’s length is proportional to the average speed during its interval, so the chart forms a speed-time graph.
Which side of the carbon disc should face the tape?
The inked side faces down onto the tape, so the striker presses the carbon against the paper. If no dots appear while the striker is moving, the disc is usually upside down or worn through.
How long should each length of tape be?
Long enough to record the whole motion with some spare for threading and attaching, which usually means a little longer than the runway or the drop. Very long tapes drag and tangle, which adds friction.
Should the timer be switched on before releasing the trolley?
Yes. Start the timer first, let it settle into a steady rhythm and then release the trolley or mass. Releasing first means the start of the motion is not recorded and the first dots are irregular.
Last Updated: October 2026










Reviews
There are no reviews yet.