Search

In Stock

Thermistors NTC 150 ohms

Thermistances CTN 150 ohms Engineered with a steep Negative Temperature Coefficient (NTC), enabling precise detection of minute ambient temperature fluctuations through predictable logarithmic resistance decay.

Factory-Calibrated 150 ohms Base Features a nominal resistance at 25°C with a 10% tolerance, ensuring systemic interchangeability and data consistency across high-volume laboratory prototyping and educational sensing arrays.

₹265.00

Quick Answer: These are NTC thermistors with a nominal resistance of 150 ohms: temperature-sensitive resistors whose resistance falls as they warm. A 150 ohm NTC thermistor is used in school and college practicals as the sensing element of temperature-dependent potential dividers and to investigate how resistance changes with temperature.

What 150 Ohms Means

A thermistor’s resistance changes with temperature, so a single value only makes sense alongside a reference temperature. The 150 ohm figure in the name is the nominal resistance at that reference point, which by convention for thermistors is usually 25 °C. Colder than that the resistance is higher; warmer, it is lower, falling steeply as the temperature climbs. The reference temperature, tolerance and B value of these parts should be confirmed before precise work.

A value of 150 ohms is low for a thermistor. That matters in practice, because a low resistance draws more current from a given supply, and a thermistor carrying current also heats itself. Circuits for these parts therefore need a little more thought than for high-value thermistors, which is a useful design lesson in its own right.

Designing the Potential Divider

To turn the resistance change into a voltage, the thermistor goes in series with a fixed resistor across the supply. The output changes fastest with temperature when the fixed resistor is close to the thermistor’s resistance in the middle of the range of interest. For measurements around room temperature, a fixed resistor near 150 ohms is a sensible starting point; for a range centred higher, a smaller value is chosen. Students can test this by trying several fixed resistors and comparing how far the output moves for the same change in water temperature.

Self-heating sets the limit. The power dissipated in the thermistor equals the voltage across it squared divided by its resistance, so with a low resistance even a modest voltage warms it noticeably above its surroundings, and the circuit then reports too high a temperature. Keeping the supply to the divider low, or adding series resistance, keeps the error small, and comparing readings at two supply voltages shows the effect clearly.

Applications

  • Temperature-sensing potential dividers that drive a transistor, LED or 6 V buzzer
  • Investigating how resistance falls with temperature in a water bath
  • Showing self-heating by comparing readings at two supply voltages
  • Project work on thermostats and frost alarms

Specifications

Component NTC thermistors
Nominal resistance 150 ohms (as titled)
Behaviour Resistance falls as temperature rises
Typical circuit Potential divider with a fixed resistor
Reference temperature, tolerance and B value Confirm at enquiry

Care & Handling

  • Keep the voltage across each 150 ohm NTC thermistor low to limit self-heating.
  • Seal the leads in a dry tube or sleeve before using the thermistors in a water bath.
  • Avoid sharp bends in the leads close to the body.
  • Label and store them separately from other thermistors so different values are not mixed.

Why Choose LabEquip

Teachers ordering several thermistors for a class usually want matched values so every group’s results can be compared. LabEquip supplies these 150 ohm parts with the general-purpose NTC thermistor and other physics lab equipment; ask about quantities through the contact page.

Frequently Asked Questions

At what temperature is the 150 ohm value measured?

The nominal resistance of a thermistor is quoted at a reference temperature, conventionally 25 °C for most parts. Below it an NTC thermistor’s resistance is higher than 150 ohms, and above it lower. The reference temperature for these parts should be confirmed at enquiry.

What fixed resistor should I use with it in a potential divider?

For the greatest sensitivity, choose a fixed resistor close to the thermistor’s resistance in the middle of the temperature range you want to measure. Around room temperature that means a value near 150 ohms; for a hotter range, use a smaller value.

Why does the reading drift upward when the circuit is left on?

Current through the thermistor warms it above the surrounding temperature. Its resistance falls, and the circuit reports a higher temperature than the real one. Lowering the voltage across it, or switching on only while reading, reduces this self-heating.

Why does a low-value thermistor heat itself more than a high-value one?

The power dissipated equals the voltage squared divided by the resistance. At the same voltage a 150 ohm thermistor dissipates far more power than one of several thousand ohms, so it warms more and needs a lower supply or extra series resistance.

How is the change of resistance with temperature described?

By the B value, a constant for the thermistor material. It links the resistances at two temperatures through an exponential relationship, so from the nominal value and the B value the resistance at any temperature within range can be estimated.

Can these thermistors be used for frost or overheat alarms?

Yes. In a potential divider feeding a transistor or comparator, a falling temperature raises the thermistor’s resistance and can trigger a frost alarm, while a rising temperature can trigger an overheat warning, depending on which position the thermistor takes in the divider.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
INR Indian rupee
Product has been added to your cart
Compare (0)