Search

In Stock

Pressure Surface Model

Maquette Pression Surface 3 diamètres différents pour investiguer, Features discrete, factory-calibrated cross-sectional areas to provide immediate comparative analysis of substrate indentation depth under constant force vectors.

High-Stability Load Platform Constructed from a corrosion-resistant alloy with a precision-leveled surface to ensure uniform vertical force application and eliminate lateral measurement bias during trials.

$27.64

Quick Answer: The pressure and surface area model is a classroom demonstration of how the effect of a force depends on the area it acts on. The same load resting on a smaller area produces a higher pressure, which students see before they meet the formula p = F/A.

One Force, Different Areas

In models of this kind a block or loaded base rests on a yielding surface such as sand, foam or modelling clay, first on a large face and then on a small one, and the depth of the imprint is compared. The weight does not change between the two trials; only the area carrying it does. The deeper imprint under the small face is a visible measure of the higher pressure.

Putting numbers on it makes the point firm. A 1 kg block weighs about 9.8 N. Resting on a face of 50 cm², which is 0.005 m², it exerts roughly 2 kPa; turned onto a face of 10 cm² it exerts nearly 10 kPa, five times as much, because the area is one fifth. The unit is the pascal, one newton per square metre, so areas in square centimetres must be converted before dividing.

Everyday Examples to Discuss

Snowshoes, wide tractor tyres and the broad feet of camels spread a weight over a large area so it does not sink. Knife blades, needles and the point of a drawing pin do the opposite, concentrating a modest force on a tiny area to cut or pierce. A person standing on one foot exerts twice the pressure on the floor that they do on two, without becoming any heavier.

After the demonstration, students can estimate their own standing pressure by drawing round their shoes on squared paper, counting the squares and dividing their weight in newtons by the area in square metres.

Lessons It Supports

  • Introducing pressure as force per unit area in middle-school science
  • Practising unit conversion from square centimetres to square metres
  • Explaining snowshoes, tyres, knives and drawing pins
  • Leading into the separate topic of pressure in liquids

Specifications

Product Demonstration model for pressure and contact area
Principle shown p = F/A: the same force over a smaller area gives a higher pressure
Observation Comparison of the effect of one load on areas of different size
Units used Force in newtons, area in square metres, pressure in pascals
Form of the model and surface material Confirm at enquiry

Care & Handling

  • Level the soft surface between trials so each imprint starts from the same flat state
  • Lower the load gently rather than dropping it, so the comparison is fair
  • Keep sand or clay covered when stored so it does not dry out or collect dust
  • Wipe the model clean after use

Why Choose LabEquip

Teachers introducing pressure want something students can see and measure before any formula is written, and this model does exactly that. It leads naturally into liquid pressure with Pascal’s sphere; contact LabEquip to confirm the model’s form and supply, or browse more physics lab equipment.

Frequently Asked Questions

Why does the small face sink deeper if the weight is the same?

The weight is the same but it is spread over a smaller area, so each square centimetre of the surface carries more force. That higher pressure pushes the soft material aside further.

What unit is pressure measured in?

The pascal, one newton per square metre. Because a pascal is small, classroom answers are often given in kilopascals, and areas measured in square centimetres must be converted to square metres before dividing.

How can students calculate the pressure they exert when standing?

Draw round both shoes on centimetre-squared paper, count the squares to estimate the area, convert to square metres and divide their weight in newtons by it. Standing on one foot doubles the result.

Does the pressure depend on the shape of the contact area?

No, only on its size. A long thin face and a square face of equal area give the same pressure under the same force, which makes a useful extra check with the model.

Why are drawing pins pointed at one end and flat at the other?

The point has a tiny area, so the thumb’s force produces a very high pressure that pierces the board, while the wide head spreads the same force over the thumb so the pressure there stays low.

Is this the same as pressure in liquids?

It is the same quantity, force per unit area, but the model deals with a solid pressing on a surface. Liquid pressure adds the ideas that pressure rises with depth and acts in all directions, which is the next lesson.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
USD United States (US) dollar
Product has been added to your cart
Compare (0)