Search

In Stock

Poisson’s Ratio of Rubber Apparatus

Heavy-Duty Tension System: Constructed with a reinforced metallic frame and high-quality rubber specimen mounting, engineered to provide uniform axial stretching without slippage during load application.

Dual-Axis Measurement Interface: Equipped with a precision micrometer or vernier gauge and a graduated linear scale to capture simultaneous changes in specimen length and diameter with sub-millimeter accuracy.

₹665.00

Quick Answer: The Poisson’s Ratio of Rubber Apparatus determines Poisson’s ratio of rubber by loading a vertical rubber tube and measuring how both its length and its internal volume change. Because rubber stretches so far, both changes are large enough to read with simple scales.

Measuring Two Strains in a Rubber Tube

Poisson’s ratio σ compares the lateral strain of a stretched material with its longitudinal strain. Lateral strain is hard to measure directly on a metal wire, but rubber tubing makes it accessible: as the tube stretches, its cross-section shrinks, and the change shows up as a change in the volume of water it holds.

In the usual arrangement the tube hangs from a rigid support with its lower end closed and attached to a mass hanger, while its upper end connects to a narrow graduated glass tube or burette. The rubber tube is filled with water up to a mark in the glass tube. Adding load stretches the tube; the increase in length is read with a pointer and scale and the change in internal volume from the movement of the water level. For small changes, σ = ½(1 – (1/A)(dV/dL)), where A is the internal cross-sectional area.

Rubber gives a value close to 0.5, the figure for a material whose volume hardly changes when stretched, which is a useful check on the method. The two-bar rigidity apparatus finds Poisson’s ratio for a metal wire from oscillation periods instead. The tube, glass tube and scale supplied with this listing should be confirmed.

Specifications

Measures Poisson’s ratio of rubber
Specimen Rubber tube hung vertically and filled with water
Readings Increase in length and change in internal volume
Relation used σ = ½(1 – (1/A)(dV/dL))
Parts supplied Confirm at enquiry

Applications

  • Determining Poisson’s ratio of rubber
  • Estimating the Young’s modulus of rubber from the load and extension readings
  • Observing elastic hysteresis by comparing loading and unloading
  • Discussing why nearly incompressible materials give a ratio close to one half

Care & Handling

  • Add loads gently and wait for the pointer and water level to settle before reading.
  • Remove the loads after the practical; rubber left stretched takes a permanent set.
  • Store the rubber tube away from sunlight and heat, which make rubber brittle.
  • Fill the tube slowly to keep air bubbles out of the water column.

Why Choose LabEquip

Undergraduate physics practical courses include Poisson’s ratio for rubber because it shows lateral strain directly, which a metal wire cannot. LabEquip lists this apparatus in Physics Equipments; confirm the parts supplied via the contact page.

Frequently Asked Questions

Why is rubber used as a tube rather than as a solid strip?

A water-filled tube turns the shrinking of its cross-section into a change of volume, which a narrow glass tube shows as a clear movement of the water level. That makes the lateral strain measurable with simple equipment.

Why is Poisson’s ratio for rubber close to 0.5?

Rubber is nearly incompressible, so its volume stays almost constant as it stretches. A material that keeps its volume exactly has a ratio of 0.5, the theoretical upper limit for a stable isotropic material.

Why should readings be taken after a short wait?

Rubber keeps stretching slowly for a while after a load is added, an effect called creep. Waiting until the pointer and water level settle gives consistent readings.

How are air bubbles removed?

Fill the tube slowly from the top with the lower end closed, tapping it gently as the water rises. Trapped bubbles expand and compress with the load and spoil the volume readings.

Can the same apparatus give Young’s modulus for rubber?

Yes, approximately. The load and extension readings give the stress and strain in the tube wall, from which Young’s modulus is calculated using the cross-sectional area of the rubber itself.

Why does rubber give different readings on loading and unloading?

Rubber shows elastic hysteresis: some energy turns into heat during each cycle, so the unloading curve lies below the loading curve. Recording both and averaging gives a fairer value.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
INR Indian rupee
Product has been added to your cart
Compare (0)