Search

In Stock

MAGNETIC NEEDLE ON STAND (OERSTED DEVICE)

Low-Friction Pivot Geometry: Features a jewel-mounted cobalt steel needle engineered for extreme sensitivity to low-magnitude magnetic flux gradients generated by adjacent DC conductors.

Non-Inductive Support Architecture: Integrated with a non-magnetic brass pillar and high-conductivity copper rails designed to eliminate parasitic magnetic interference while sustaining high-amperage current throughput during field mapping.

$5.02

Quick Answer: The Magnetic Needle on Stand (Oersted Device) is a pivoted magnetic needle arranged with a straight conductor so that a current through the conductor visibly deflects the needle. The Oersted device repeats the 1820 observation that an electric current produces a magnetic field, the starting point of electromagnetism.

Current, Field and Needle

Around any wire carrying a current there is a magnetic field whose lines form circles centred on the wire. A magnetic needle near the wire feels this field in addition to the Earth’s field and turns to line up with the combination. In the usual form of this apparatus a straight conductor, with a terminal at each end, is mounted parallel to the needle and a short distance above or below it; the details of the conductor and terminals on this model can be confirmed at enquiry.

Because the circular field points one way above the wire and the opposite way below it, the needle turns in opposite directions depending on whether the conductor lies over it or under it. Reversing the current reverses the deflection too.

Setting Up the Experiment

Before connecting anything, turn the whole stand until the conductor lies exactly along the direction in which the needle rests. The current’s field then acts across the needle, giving the clearest swing. Connect the conductor through a switch and a rheostat or series resistor to a low-voltage DC supply such as a battery eliminator; a bare conductor has almost no resistance, so it must never be connected straight across a supply. Close the switch only briefly for each observation, so that nothing overheats.

From Deflection to Measurement

The needle settles along the resultant of the Earth’s horizontal field and the field of the wire, so the tangent of the deflection angle equals the ratio of the two. With an ammeter in series, students can record the deflection for several currents and plot the tangent of the angle against current. A straight line shows that the field of the wire is proportional to the current, the principle used in the tangent galvanometer.

Applications

  • Repeating Oersted’s discovery of the magnetic effect of a current
  • Showing that the deflection reverses with the current and with the wire above or below the needle
  • Practising the right-hand grip rule for the direction of the field around a wire
  • Plotting the tangent of the deflection against current as an introduction to the tangent galvanometer

Specifications

Type Pivoted magnetic needle on stand arranged for the Oersted experiment
Shows Magnetic field produced by an electric current
Supply needed Low-voltage DC source with a switch and current-limiting resistance
Related measurement Deflection angle compared with current
Conductor form, terminals, needle length and base Confirm at enquiry

Care & Handling

  • Always include a resistance or current-limited supply; never connect the bare conductor directly across a cell or supply.
  • Switch the current on only for the few seconds needed to read the deflection.
  • Keep the Oersted device away from steel benches, magnets and other current-carrying leads during readings.
  • Check that the terminals are tight and the needle swings freely before each lesson.

Why Choose LabEquip

Schools and colleges teaching electromagnetism buy this apparatus because it turns a key historical experiment into a clear bench demonstration. LabEquip lists it with its physics lab equipment; the plain magnetic needle on stand suits magnetism lessons without a current. Send class sizes and supply details through the contact page.

Frequently Asked Questions

What did Oersted’s experiment show?

It showed for the first time that an electric current produces a magnetic field. A compass needle near a current-carrying wire is deflected, linking electricity and magnetism and opening the way to motors, generators and electromagnets.

Why does the needle turn the other way when the wire is under it?

The field around a wire forms circles. Above the wire the field points in one direction and below it in the opposite direction, so the needle is pushed round the opposite way.

How can I predict which way the needle will turn?

Use the right-hand grip rule: point the thumb of the right hand along the conventional current and the curled fingers give the direction of the field. The north-seeking end of the needle turns towards that direction at its position.

How does the deflection depend on the current?

The needle lines up with the resultant of the field of the Earth and the field of the wire. The tangent of the deflection angle is proportional to the current, so doubling the current does not double the angle but does double its tangent.

What supply should be used with the Oersted device?

A low-voltage DC supply with a switch and a rheostat or series resistor to limit the current. Because the straight conductor has very little resistance, connecting it directly to a supply would draw a large current and heat the circuit.

How does this differ from the plain magnetic needle on stand?

The plain version is a needle alone, used to detect magnetic fields from magnets. This version places a conductor in line with the needle so the field of an electric current can be shown without extra clamps and wires.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
USD United States (US) dollar
Product has been added to your cart
Compare (0)