Search

In Stock

FIXED ELECTRICAL RESISTORS

Precisely rated resistance values with low tolerance variation for accurate circuit analysis

Heat-stable construction with insulated leads supporting safe, repeated laboratory use

$1.69

Quick Answer: Fixed Electrical Resistors are components with a set resistance that cannot be adjusted, used to control current and divide voltage in circuits. In physics laboratories fixed electrical resistors are the standard components for Ohm’s law, series and parallel combination, potential divider and meter-bridge practicals.

Reading and Choosing a Resistor

Small carbon-film and metal-film resistors carry their value as coloured bands. The first two (or three) bands give digits, the next gives the multiplier, and a final band, often gold or silver, gives the tolerance: how far the actual value may differ from the marked one. A resistor with bands brown, black, red and gold, for example, is 10 × 100 = 1000 ohms, within 5 percent. Larger wire-wound resistors usually have their value printed directly.

Every resistor also has a power rating, the rate at which it can safely turn electrical energy into heat. Power equals current squared times resistance, so a low resistance carrying a large current can overheat even at low voltage. The types, values, power ratings and mounting of the resistors in this listing should be confirmed when ordering; sets are made up in many combinations.

Practicals Built on Fixed Resistors

Ohm’s law is the starting point: with a fixed resistor, a variable supply or rheostat, an ammeter and a voltmeter, students plot voltage against current and find a straight line through the origin whose gradient is the resistance. Two or three resistors then show the combination rules: in series the resistances add, while in parallel the reciprocals add, so the total is less than the smallest. A pair of resistors across a supply forms a potential divider, sharing the voltage in proportion to their resistances, which is the principle behind sensors and volume controls.

Practicals

  • Verifying Ohm’s law and finding resistance from a voltage-current graph
  • Testing the rules for resistors in series and in parallel
  • Building potential dividers and current-limiting circuits for LEDs
  • Using known resistors as standards in meter-bridge and potentiometer practicals; the series resistor network apparatus extends the combination work

Specifications

Type Fixed-value resistors for circuit work
Common types Carbon film, metal film, wire-wound
Marking Colour bands or printed value, with tolerance
Uses Ohm’s law, combinations, potential dividers, current limiting
Values, power rating, number and mounting Confirm at enquiry

Care & Handling

  • Check each resistor’s power rating against the expected current before switching on.
  • Switch off between readings so the fixed electrical resistors do not warm up and change value during an experiment.
  • Avoid bending the leads of small resistors repeatedly at the body, where they break most easily.
  • Store resistors sorted by value in labelled compartments so the colour codes do not have to be read every time.

Why Choose LabEquip

Physics laboratories need a good stock of fixed resistors because almost every circuit practical uses them. LabEquip lists this item in its physics lab equipment range; single-value resistors such as the 5 ohm resistor are also available for Ohm’s law sets. Ask about values and power ratings through the LabEquip contact page.

Frequently Asked Questions

How do I read a resistor’s colour code?

Read from the end with the bands closest together. The first two bands are digits, the third is the multiplier (a power of ten) and the last is the tolerance. Brown, black, red, gold means 10 times 100, or 1000 ohms, within 5 percent.

What does the tolerance band mean?

It gives how far the actual resistance may differ from the marked value. A gold band means within 5 percent and silver within 10 percent, so a marked 100 ohm resistor with a gold band may measure anywhere from 95 to 105 ohms.

Why does a resistor have a power rating?

A resistor turns electrical energy into heat at a rate equal to current squared times resistance. If that rate exceeds the power rating, the resistor overheats, changes value or burns out.

How do series and parallel combinations change the total resistance?

In series the resistances simply add, so the total is larger than any one. In parallel the reciprocals add, so the total is smaller than the smallest resistor in the group.

Why does a measured value differ from the marked value?

Because of the tolerance, the resistance of the connecting leads and contacts, the meter’s own accuracy, and heating of the resistor, which changes its resistance slightly as the current flows.

Which resistors suit a potential divider practical?

Two resistors of the same order of magnitude, so that the output voltage changes noticeably when one is replaced. Equal values give half the supply voltage, a useful first check.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
USD United States (US) dollar
Product has been added to your cart
Compare (0)