Quick Answer: The Filtration Flask is a thick-walled conical flask with a short side arm near the neck, used to collect the filtrate when liquids are drawn through a filter under reduced pressure. Connected to a vacuum source and fitted with a Buchner or Hirsch funnel, this flask makes filtering fine solids much faster than gravity filtration.
How Vacuum Filtration Works
In ordinary filtration, only the weight of the liquid pushes it through the filter paper, which is slow for fine precipitates. In vacuum filtration, a pump lowers the air pressure inside the flask through the side arm. The atmosphere above the funnel then presses down on the liquid with a much larger force than gravity alone, driving it through the paper and leaving a firmly packed, nearly dry solid on top. The pressure difference across the filter, not suction pulling from below, is what does the work, which makes the set-up a useful illustration of atmospheric pressure.
The funnel sits in the flask’s neck on a rubber cone, bung or adapter that makes an airtight seal. Thick tubing that will not collapse under reduced pressure joins the side arm to a water aspirator pump or a vacuum pump, ideally through a second empty flask acting as a trap.
Why the Flask Is Built Differently
A flask under vacuum carries the full pressure of the atmosphere on its outer surface. Ordinary thin-walled conical flasks are not made for this and can implode, so flasks for vacuum work are made with heavy walls, and many are made from borosilicate glass, which also resists thermal shock. Plastic versions exist as well. The material and capacity of this flask should be confirmed when ordering. Whatever the material, the flask should be checked for chips and star cracks before each use, because a flaw that is harmless at normal pressure can fail under vacuum.
Uses
- Collecting crystals after recrystallisation in chemistry practicals
- Separating fine precipitates that clog or pass slowly through gravity filters
- Demonstrating the force exerted by atmospheric pressure
- Use as a trap flask between a filtration set-up and a water aspirator or vacuum pump
Care & Handling
- Clamp the filtration flask to a stand while it is under vacuum so it cannot tip over.
- Never heat the flask while it is under reduced pressure, and do not use it as a general heating vessel.
- Release the vacuum by disconnecting the tubing before turning off a water aspirator, to stop water being sucked back into the flask.
- Inspect for chips, scratches and star cracks before each use, and retire any damaged flask.
Specifications
| Type | Heavy-walled conical flask with side arm (Buchner flask) |
| Use | Collecting filtrate in vacuum filtration |
| Used with | Buchner or Hirsch funnel, rubber cone or bung, vacuum tubing, pump, trap flask |
| Principle | Atmospheric pressure drives liquid through the filter |
| Material and capacity | Confirm at enquiry |
Why Choose LabEquip
Chemistry, biology and pharmacy laboratories keep several of these flasks because vacuum filtration is used in many routine preparations. LabEquip currently lists this flask in Physics Equipments; rubber cones for filtration flasks provide the seal between flask and funnel. For material and capacity, contact us through the LabEquip contact page.
Frequently Asked Questions
Why do filtration flasks have thick walls?
Under vacuum, the outside air pushes on every part of the flask with the full force of atmospheric pressure. Thick walls let the flask withstand that load, where a thin ordinary flask could implode.
Can an ordinary conical flask be used for vacuum filtration?
No. Ordinary conical flasks have thin walls designed for normal pressure and may implode when evacuated, scattering glass. Only flasks made for vacuum work should be connected to a pump.
Why should a trap be fitted between the flask and the pump?
A trap is an empty flask that catches any liquid drawn over from the main flask, and any water that flows back from an aspirator. It protects both the pump and the filtrate.
Why must the tubing be disconnected before the water pump is turned off?
When the water flow stops, the pressure in the aspirator rises and water can be sucked back into the evacuated flask, contaminating the filtrate. Releasing the vacuum first prevents this.
Can the flask be heated?
Not while it is under vacuum, and it is not designed as a heating vessel. The thick glass heats unevenly and can crack, so solutions should be heated in a beaker or round-bottom flask before filtering.
What makes the seal between the funnel and the flask?
A rubber cone, a bored rubber bung or a flexible adapter fitted in the neck. It must make an airtight seal, otherwise air leaks in and the filtration slows down.
Last Updated: October 2026










Reviews
There are no reviews yet.