Quick Answer: The Electric Tuning Fork for Melde’s experiment is an electrically maintained tuning fork from a set of rust-resistant stainless steel forks, made to keep vibrating steadily while connected to a low-voltage supply. In Melde’s experiment the electrically maintained tuning fork drives a stretched string into standing waves so the frequency or the string’s linear density can be measured.
How an Electrically Maintained Fork Works
A tuning fork struck by hand rings for a few seconds and fades. For Melde’s experiment the string must be driven at a steady amplitude for as long as readings take, so the fork is kept going electrically. One prong sits near a small electromagnet. A contact on the prong completes the electromagnet’s circuit when the prong is at rest; the magnet pulls the prong, the contact opens, the magnet releases it and the prong springs back. Like a bell’s trembler, this make-and-break action feeds a little energy in on every cycle, and the fork vibrates at its own natural frequency.
These forks are made of stainless steel, which resists rusting. That matters for a frequency standard: corrosion would change the mass of the prongs and shift the pitch over time. The number of forks in the set and their frequencies should be confirmed when ordering.
Melde’s Experiment in Two Arrangements
A light string is tied to one prong, passed over a pulley and loaded with a scale pan and masses to set its tension T. Adjusting the tension or the length until the string divides into clear loops gives standing waves. In the transverse arrangement, the prong vibrates at right angles to the string and the string vibrates at the fork frequency n, so n = (p/2l)√(T/m), where p is the number of loops in length l and m is the mass per unit length. In the longitudinal arrangement, the prong moves along the string, which then completes only one vibration for every two of the fork, so n = (p/l)√(T/m).
Seeing the number of loops halve when the fork is turned from the transverse to the longitudinal position, at the same tension, is the most striking result of the practical.
Specifications
| Type | Electrically maintained tuning fork for Melde’s experiment |
| Material | Stainless steel, rust resistant (as titled) |
| Supplied as | A set of tuning forks |
| Drive | Electromagnet and make-and-break contact on low-voltage DC |
| Number of forks, frequencies and supply voltage | Confirm at enquiry |
Practicals
- Melde’s experiment in transverse and longitudinal arrangements
- Determining the frequency of the fork from the number of loops, tension and linear density
- Finding the linear density of a string with a fork of known frequency
- Verifying that tension divided by the square of the loop count stays constant, using Melde vibrator cord and slotted weights
Care & Handling
- Run the electrically maintained tuning fork only from a low-voltage DC supply at its rated voltage.
- Adjust the contact screw in small steps until the prongs vibrate steadily without excessive sparking.
- Clamp the fork firmly so it does not walk across the bench while vibrating.
- Clean the contact gently when it becomes blackened, and store the forks clean and dry.
Why Choose LabEquip
Physics departments in schools and colleges buy these forks for the stationary-waves practicals in their senior syllabus. LabEquip lists them in its physics lab equipment range, alongside the cords and weights the experiment needs. Ask about the frequencies in the set through our contact page.
Frequently Asked Questions
How does an electrically maintained tuning fork keep vibrating?
A small electromagnet near one prong is switched on and off by a contact that the prong itself opens and closes. Each pull adds a little energy, so the fork keeps vibrating at its natural frequency instead of dying away.
Why does the string vibrate at half the fork frequency in the longitudinal arrangement?
When the prong moves along the string, the string is pulled tight once per fork cycle but swings to each side only once in every two cycles. Its transverse vibration therefore has half the frequency of the fork.
How is the fork frequency found from the experiment?
In the transverse arrangement, the frequency equals the number of loops divided by twice the string length, multiplied by the square root of tension divided by mass per unit length. In the longitudinal arrangement the result is doubled.
Why are the forks made of stainless steel?
Stainless steel resists rust. Corrosion on ordinary steel would add or remove material from the prongs and slowly change the frequency, so a rust-resistant fork keeps its pitch for much longer.
How do I get clear, steady loops on the string?
Set the fork vibrating steadily first, then adjust the tension with the masses, or the length, until the loops are sharp with still nodes. Small changes make a big difference near the right setting.
What power supply does the fork need?
A low-voltage direct-current supply, such as cells or a bench power supply, at the voltage the fork is designed for. Too high a voltage causes heavy sparking at the contact and uneven vibration.
Last Updated: October 2026










Reviews
There are no reviews yet.