Search

In Stock

Digital Moisture Meter for Wood

High-Precision Electronic Sensor: Delivers reliable moisture readings across diverse wood types with minimal error.

Instant Digital Display with Range Selection: Allows quick interpretation and logging of moisture percentages for analysis and experimentation.

₹7,025.00

Quick Answer: The Digital Moisture Meter for Wood is a portable electronic instrument that gives the water content of timber as a percentage of its oven-dry mass, based on an electrical measurement. Carpenters, timber stores and materials-science classes use a digital moisture meter for wood to check that timber is dry enough for its intended use.

Water in Wood and the Fibre Saturation Point

Water in timber exists in two forms. Free water fills the cell cavities of green wood, while bound water is held within the cell walls. As wood dries, the free water leaves first; the point at which the cavities are empty but the walls are still saturated is the fibre saturation point, commonly put at around 25 to 30 percent moisture content for many species. Below that point, further drying removes bound water, and only then does the wood begin to shrink and gain strength.

Electrical meters are most reliable below fibre saturation, which is fortunately the range that matters for joinery and construction. The electrical resistance of wood falls steeply as its bound water increases, so a small change in moisture produces a large change in the reading; above fibre saturation the change is much smaller and readings become rough estimates.

Specifications

Instrument Electronic timber moisture meter
Reads Moisture content of timber as a percentage of oven-dry mass
Basis Electrical properties of wood, which change with bound water content
Most reliable range Below the fibre saturation point
Sensing type (pin or pinless), species settings and range Confirm at enquiry

Equilibrium Moisture and Why It Matters

Wood exchanges moisture with the surrounding air until it reaches its equilibrium moisture content, which depends on the relative humidity and temperature of the air. Timber dried for an air-conditioned interior will swell if fitted in a damp outbuilding, and wood dried for outdoor use will shrink and crack indoors. Measuring the timber, and comparing the reading with the equilibrium value expected where it will be used, avoids gaps in floorboards, sticking doors and split furniture joints.

Uses and Investigations

  • Checking timber before joinery, flooring and furniture making
  • Monitoring kiln or air drying of planks over several weeks
  • Checking that firewood is seasoned enough to burn cleanly
  • Materials science investigations of drying curves and shrinkage
  • Detecting damp in wooden structures after leaks

Care & Handling

  • If the meter uses pins, push them into the wood straight and withdraw them straight, so they do not bend or snap.
  • Wipe resin and sawdust off the contacts after use.
  • Keep the meter dry and remove the battery for long storage.
  • Use the check function or reference block, where provided, to confirm the meter before an important batch of measurements.

Why Choose LabEquip

Woodworking workshops, construction-skills courses and timber yards buy moisture meters for routine checks before cutting and fitting. LabEquip lists this meter in Physics Equipments; a related electronic meter for crops is the digital moisture meter for grain. For species settings and sensing type, contact us via the LabEquip contact page.

Frequently Asked Questions

What is the fibre saturation point?

It is the moisture content at which the cell cavities in wood have lost their free water but the cell walls are still fully saturated. Below it, wood shrinks as it dries and its strength increases, and electrical moisture readings are most dependable.

Why does wood shrink more across the grain than along it?

The cellulose fibres in the cell walls run mostly along the length of the tree. Losing bound water draws the fibres closer together sideways but hardly shortens them, so a board shrinks noticeably in width and thickness and very little in length.

What is equilibrium moisture content?

It is the moisture level wood settles at when left long enough in air of a given humidity and temperature. Damp air gives a higher equilibrium value and dry, heated air a lower one, so timber should be dried to suit where it will be used.

How can I tell whether firewood is seasoned?

Split a log and measure the freshly exposed face across the grain, not the dry outer surface. Seasoned firewood reads well below freshly cut wood, burns hotter and produces less smoke.

Can the meter follow a drying experiment?

Yes. Weigh small boards and take a meter reading at regular intervals while they dry. Plotting moisture against time shows a drying curve that slows as the wood approaches equilibrium with the room air.

Why are readings in treated or painted wood unreliable?

Preservative salts make wood conduct more easily and raise resistance-based readings, while thick paint or varnish insulates the surface and affects surface-sensing meters. Measure an untreated, unfinished area where possible.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
INR Indian rupee
Product has been added to your cart
Compare (0)