Search

In Stock

Balance, Double Beam

Precision-Ground Agate Bearings: Utilizes specialized, friction-reducing agate stone pivots at the fulcrum to ensure maximum beam sensitivity and repeatable measurement linearity over intensive duty cycles.

Tiered Notched Beam System: Features two precision-engraved beams with sliding stainless steel poise weights, allowing for high-resolution readability and rapid zero-point taring without the requirement for external weight sets.

$11.73

Quick Answer: A double beam balance is a mechanical balance with two graduated beams and sliding riders, used in school laboratories for quick mass measurement without a weight box. The double beam balance gives its reading by adding the positions of the two riders once the beam swings level.

Two Beams, Coarse and Fine

One beam is graduated in large steps and the other in small ones. The rider on the coarse beam sets the bulk of the reading and the rider on the fine beam adds the remainder, so a student moves the large rider until the beam tips, steps it back, and then slides the small rider until the pointer shows balance. The total is the coarse rider value plus the fine rider value.

Moving a rider changes its distance from the pivot and therefore its moment, which is how two small sliding masses can balance a wide range of loads. With fewer settings than a triple beam model, the two-beam design is quicker for younger students and for routine checks where the finest division is not needed.

Setting Up for a Lesson

Stand the balance on a firm, level bench, slide both riders to zero and turn the zero knob or counterweight until the pointer rests on its mark. Put objects gently in the centre of the pan and wait for the beam to stop swinging before reading. Teaching students to read the pointer straight on at eye level removes most of the differences between groups’ results.

Typical School Uses

  • Weighing samples and containers in middle-school science activities
  • Measuring masses for the density of regular and irregular solids
  • Comparing the masses of reactants and products in simple chemical changes
  • Demonstrating the balance of moments with movable riders

Specifications

Type Mechanical rider balance with two graduated beams
Principle Moments about a pivot
Reading Sum of the coarse and fine rider values
Power None required
Pan arrangement, capacity and graduation Confirm at enquiry

Care & Handling

  • Slide both riders back to zero before putting the balance away.
  • Place objects on the pan rather than dropping them, to protect the pivot.
  • Wipe the pan and beams with a dry cloth and keep the graduations free of grit so the riders seat correctly.

Why Choose LabEquip

Middle schools and lower secondary labs choose the double beam balance where speed and simplicity matter more than the finest division. If you need more resolution, compare the triple beam balance in the same physics equipment category; quantities can be discussed through LabEquip’s contact page.

Frequently Asked Questions

When is a double beam balance better than a triple beam balance?

When students need quick readings and the finest step of a triple beam balance is not required. Fewer riders mean fewer settings and fewer chances of a rider being left out of place.

Why does the pointer keep swinging after I place an object?

The beam oscillates about its pivot until friction and any damping bring it to rest. Wait for it to settle, or read the centre of a small, even swing rather than one end of it.

How do I check that the balance is accurate?

Weigh a known mass from a calibrated weight set and compare the reading. If it is off, re-zero with the pan empty and riders at zero, then test again.

Can the riders be removed for cleaning?

Riders are designed to stay on their beams. Forcing them off can bend the beam or damage the notches, so clean around them in place.

What should I do if the zero keeps changing?

Check that the bench is level and steady, that nothing touches the pan or beam, and that the pivot is clean. A zero that still wanders may point to a damaged pivot needing repair.

Is a double beam balance suitable for weighing chemicals?

Yes, in a container such as a watch glass or weighing boat. Subtract the container’s mass and keep corrosive powders away from the pan and pivot.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
USD United States (US) dollar
Product has been added to your cart
Compare (0)