Search

In Stock

Surface Tension Measurement Device

Dispositif d'étude de la tension superficielle, Adjustable Vertical Liquid Platform Enables the technical Evaluation of film breakage points and meniscus formation across varied liquid densities.

Low-Friction Pivot Bearings  Mesurer le coefficient de tension superficielle, supporting the Application of the Du Noüy principle in vocational laboratory settings, ensuring high-fidelity data acquisition with minimal parasitic drag.

Interchangeable Wire Loops Montrer l'influence de la température et du type de liquide mis en oeuvre, Encourages student Synthesis of surface tension coefficients for different solutes and surfactants in Advanced Chemistry curricula.

₹2,350.00

Quick Answer: The surface tension measurement device is a pull-off arrangement in which a detachment ring hangs from a sensitive spring force meter above a dish of liquid. With the surface tension measurement device students lower the liquid slowly, read the largest force before the liquid film breaks and calculate the surface tension.

Running a Measurement

Set up the surface tension measurement device with the force meter on a stand and the ring hanging level, then raise a wide dish of the liquid on a lab jack until the ring just touches the surface. Note the force meter reading with the ring hanging freely in air; this is the ring’s own weight, P.

Now lower the jack very slowly. The liquid clings to the ring, a thin film stretches beneath it, and the force meter reading climbs. Watch the scale continuously and note the largest reading, F, just before the film snaps. The surface tension then follows from γ = (F − P)/(4πr), where r is the ring radius.

How Small the Force Is

The extra pull from the film is small. For water, with γ about 0.072 N/m, a ring of 3 cm radius gives F − P ≈ 4π × 0.03 × 0.072 ≈ 0.027 N. That is the weight of under 3 g, which is why the device needs a sensitive force meter with a small full-scale value rather than an ordinary school spring balance.

Repeating the measurement three or four times and averaging the peak readings reduces the effect of a slightly early break. Recording the liquid temperature is also worthwhile, because surface tension falls as temperature rises.

Investigations

  • Measuring the surface tension of water by the pull-off method
  • Comparing water, ethanol and glycerol solutions
  • Showing the drop in surface tension when detergent is added
  • Investigating how surface tension changes with temperature

Specifications

Product Surface tension apparatus, pull-off (du Noüy) method
Detaching element Ring suspended level on fine wires
Force measurement Sensitive spring force meter
Calculation γ = (F − P)/(4πr)
Components supplied and force meter range Confirm at enquiry

Care & Handling

  • Zero the force meter with the ring hanging in air before every set of readings
  • Clean the ring and dish with detergent, then rinse well with distilled water
  • Lower the liquid smoothly; a jerk breaks the film early and gives a low reading
  • Return the force meter to its case unloaded so the spring is not left stretched

Why Choose LabEquip

The surface tension measurement device suits schools and colleges that want a ready-matched set rather than assembling a ring and force meter separately. LabEquip also sells the surface tension ring on its own and a Searle’s surface tension balance for comparison, within its physics lab equipment range; enquire with LabEquip.

Frequently Asked Questions

Why is the liquid lowered instead of the ring being pulled up?

Lowering the dish on a jack is smoother than pulling by hand, and it keeps the force meter still so its scale can be read while the force rises. A steady approach to the break gives a more reliable peak.

How large is the force being measured?

Only a few hundredths of a newton for water. With a 3 cm radius ring the film adds about 0.027 N, so a sensitive force meter is essential.

When should the reading be taken?

Watch the scale continuously and note the highest value reached just before the liquid film breaks. After the break the reading drops back to the ring’s weight.

How do temperature and detergent affect the result?

Warmer water has a lower surface tension, so the peak force falls as the liquid warms. A few drops of detergent lower it much more sharply.

Why subtract the weight of the ring?

The force meter carries the ring’s weight all the time. Only the extra force above that weight is due to the liquid film, so P is subtracted before dividing by 4πr.

Which other method can confirm the value?

Capillary rise in a fine glass tube gives an independent estimate from γ = ρghr/2 for water. Agreement within about ten percent between the two methods is a good classroom result.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
INR Indian rupee
Product has been added to your cart
Compare (0)