Quick Answer: A surface tension ring is a thin, flat-edged metal ring hung horizontally on fine wires from a single suspension point. The surface tension ring is the probe for the du Noüy detachment method: it is drawn out of a liquid surface while a sensitive force meter records the extra pull of the liquid film.
How the Ring Senses Surface Tension
When the surface tension ring touches a wetting liquid and the liquid is then lowered away from it, a film clings to the ring and is drawn up into a short collar. The film pulls on the ring along both its inner and its outer edge, so the length of liquid edge acting on it is about twice the circumference, 2 × 2πR = 4πR for a ring of mean radius R.
Just before the film breaks, the extra force is close to its maximum, F_max − W ≈ 4πRγ, where W is the weight of the ring and γ is the surface tension. Dividing the measured extra force by 4πR gives γ in newtons per metre.
What the Simple Formula Leaves Out
The liquid collar is not a perfect vertical cylinder, so precise work applies a correction factor that depends on the ring’s dimensions and the liquid’s density. Without it, classroom results for water are typically within several percent of the accepted value at room temperature, which is close enough to compare liquids and to show the effect of detergent.
The ring must hang truly horizontal. If it tilts, one side breaks free of the surface before the other, the peak force is lower and the result comes out too small. Check this by eye against the liquid surface before each run.
Specifications
| Product | Detachment ring for surface tension measurement |
| Method | Du Noüy ring (pull-off) method |
| Suspension | Fine wires to a single hook so the ring hangs level |
| Needed with it | Sensitive force meter, stand, lab jack, wide dish of liquid |
| Ring diameter and material | Confirm at enquiry |
Uses in the Laboratory
- Measuring the surface tension of water, ethanol and glycerol solutions
- Showing how a few drops of detergent lower surface tension
- Investigating the fall of surface tension as water is warmed
- Comparing a pull-off value with a result from capillary rise
Care & Handling
- Hold the ring only by its suspension; skin oil on the edge changes how the liquid wets it
- Wash in detergent solution, rinse well with distilled water and let it dry hanging
- Do not bend the ring or its wires; a distorted ring cannot hang flat
- Store it hanging or in a box where nothing can press on the edge
Why Choose LabEquip
Physics and chemistry departments that already own a sensitive force meter often buy the surface tension ring on its own as a low-cost route to quantitative surface tension work. LabEquip also offers the complete surface tension measurement device and other physics lab equipment; contact LabEquip to match the ring to your force meter.
Frequently Asked Questions
Why is the circumference counted twice?
The liquid film clings to both the inner and the outer edge of the ring, and each edge is pulled by surface tension. The total length of edge is therefore about two circumferences, or 4πR.
Why must the ring hang perfectly horizontal?
A tilted ring leaves the surface one side at a time, so the film never pulls on the whole edge at once. The peak force is lower than it should be and the calculated surface tension comes out too small.
What else is needed to use the ring?
A sensitive spring force meter or force sensor to hang it from, a stand to hold the meter, a lab jack to lower the liquid smoothly and a wide, shallow dish so the walls do not distort the surface.
Why do results differ from published values?
The simple formula ignores the shape of the liquid collar, and surface tension falls as temperature rises. Traces of grease or soap on the ring or dish also lower the result noticeably.
How should the ring be cleaned between liquids?
Rinse it in detergent solution, then thoroughly in distilled water, and let it dry without wiping the edge. Any detergent left behind will reduce the next reading, so rinse until water runs off evenly.
Can the ring show the effect of detergent?
Yes. Measure clean water first, then add a drop or two of detergent and repeat. The peak force drops clearly, because detergent molecules gather at the surface and reduce its tension.
Last Updated: October 2026










Reviews
There are no reviews yet.