Quick Answer: The Inertia Table is a flat platform hung from a torsion wire so that it twists back and forth about a vertical axis. Placing a body on the inertia table lengthens the period, and comparing periods with and without the body, and with a regular body of known inertia, gives the moment of inertia of an irregular object.
How the Torsion-Suspended Table Works
In its usual form, the apparatus is a horizontal plate or turntable clamped centrally to the lower end of a vertical wire whose upper end is fixed in a rigid support. Twisted through a small angle and released, the table oscillates about the wire, and the period obeys T = 2π√(I/C), where I is the total moment of inertia of whatever turns and C is the restoring couple per radian of twist.
The method avoids having to know C. Time the empty table to get T0. Then place a regular body, such as a disc or cylinder whose inertia I1 can be calculated, at the centre and time again to get T1. Finally replace it with the irregular body and record T. Because the wire is unchanged, the unknown moment of inertia is I = I1(T² − T0²)/(T1² − T0²). The table’s own inertia and the stiffness of the wire both cancel.
The table also gives a direct test of the parallel axis theorem. Moving a body of mass M outward from the centre by a distance d adds Md² to its moment of inertia, and the measured periods should grow accordingly. Placing two equal masses symmetrically keeps the table balanced while this is done.
Experiments
- Determining the moment of inertia of an irregular body, such as a machine part, by comparison with a regular one
- Verifying the parallel axis theorem with equal masses placed at increasing distances from the axis
- Comparing the moments of inertia of a ring and a disc of equal mass
- Finding the torsional constant of the suspension wire once a known body has been timed
- Studying angular simple harmonic motion within the elastic limit of the wire
Care & Handling
- Hang the inertia table so it is level and its centre lies directly below the clamp; a tilted table swings like a pendulum as well as twisting.
- Twist the table through a small angle with a light touch at the rim, never by turning the wire itself.
- Remove bodies from the platform after use, so the wire is not left loaded in storage.
- Inspect the wire for kinks before each practical and replace a kinked wire, because it no longer twists uniformly.
Specifications
| Apparatus | Platform suspended from a torsion wire |
| Motion | Angular oscillation about the vertical wire |
| Method | Comparison of periods: empty table, known body, unknown body |
| Result | I = I1(T² − T0²)/(T1² − T0²) for the irregular body |
| Support, wire and reference bodies supplied | Confirm at enquiry |
Why Choose LabEquip
Undergraduate and senior school laboratories use the inertia table for the irregular-body moment of inertia practical. It is listed with LabEquip’s physics lab equipment, along with the inertia disc, which makes a convenient known body. Send order details through the contact page.
Frequently Asked Questions
Why is the empty table timed first?
The table itself has a moment of inertia, and it is not usually known. Timing it alone gives T0, and subtracting T0² from the later readings removes the table’s contribution, leaving only the effect of the body placed on it.
Do I need to know the modulus of rigidity of the wire?
No. The comparison method uses the same wire for every reading, so the wire’s stiffness cancels when the ratio of the period differences is taken. Only the known body’s moment of inertia and the three periods are needed.
How many oscillations should be timed?
Time at least twenty oscillations and repeat each set two or three times. Start the stopwatch as the table passes a reference mark rather than at a turning point, where it moves slowly and the moment is hard to judge.
What can be used as the known body?
A uniform disc, with I = ½MR², or a solid cylinder standing on its end are the usual choices, because their moments of inertia follow from a mass and a radius. A thin ring, with I = MR², is another option.
How does the table verify the parallel axis theorem?
Place two equal masses at the same distance d on opposite sides of the centre and time the table. Repeat for several distances. A graph of T² against d² should be a straight line, because each mass adds md² to the moment of inertia.
Why does the table sometimes swing sideways?
A swing appears if the table is pushed off-centre when started, or if the load is not balanced about the wire. Start the twist with a gentle, even touch at opposite edges, and arrange loads symmetrically.
Last Updated: October 2026










Reviews
There are no reviews yet.