Search

In Stock

Venturi Model Pitot tube

Maquette Venturi tube de Pitot, Integrated Pitot Probe with Static Port enables the Evaluation of total versus static pressure differentials, allowing students to calculate local flow velocity in Advanced Fluid Mechanics modules.

Transparent Multi-Column Manometric Array supports visual Observation and high-fidelity data acquisition of pressure gradients across varied flow regimes, reinforcing evidentiary-grade laboratory reporting.

$18.61

Quick Answer: The Venturi and Pitot tube model is a flow apparatus that combines a Venturi section with a Pitot tube, so the speed of a moving fluid can be found by two independent methods. Students compare the speed from the Venturi pressure drop with the speed from the Pitot tube’s dynamic pressure.

How a Pitot Tube Reads Speed

A Pitot tube is a small tube bent to face upstream. Fluid entering its open tip is brought to rest, so the pressure inside it is the stagnation pressure, p + ½ρv². A tapping in the wall, flush with the flow, reads the static pressure p alone. The difference between the two is the dynamic pressure ½ρv², which gives the speed as v = √(2Δp/ρ).

With water flowing and the pressures read as water columns, this simplifies to v = √(2gΔh): a difference of 5 cm means about 1 m/s. If air is flowing and the manometer holds water, the density ratio must be included, and the same instrument becomes far more sensitive; a difference of only 5 mm of water then corresponds to air moving at roughly 9 m/s.

Two Methods, One Flow

The Venturi section measures speed differently. The pressure drop between the wide inlet and the narrow throat, together with the ratio of their areas, gives the throat speed from Bernoulli’s equation and continuity, and hence the flow rate. Running both methods on the same flow lets students check one against the other.

The two answers rarely agree exactly, and the difference is instructive. The Pitot tube reports the speed at its tip only, while the Venturi result reflects the average across the section. Because flow is fastest at the centre of a pipe and slowest at the wall, a centred Pitot tube usually reads a little above the mean, an introduction to the idea of a velocity profile.

Specifications

Product Flow model combining a Venturi section and a Pitot tube
Pitot tube measures Stagnation pressure, p + ½ρv²
Speed from Pitot reading v = √(2Δp/ρ)
Speed from Venturi From the inlet-to-throat pressure drop and the area ratio
Working fluid, flow source and manometer Confirm at enquiry

Applications

  • Measuring flow speed with a Pitot tube and a static tapping
  • Comparing Pitot and Venturi results for the same flow
  • Exploring why flow at the centre of a pipe is faster than near the wall
  • Explaining aircraft airspeed indicators

Care & Handling

  • Keep the Pitot tube’s mouth facing directly upstream; misalignment lowers the reading
  • Clear water drops or dust from the small tubes before each run
  • Take care not to bend the Pitot tube
  • Drain or dry the model fully after use

Why Choose LabEquip

Lecturers and senior physics teachers who want students to measure flow speed in more than one way find a combined Venturi and Pitot set-up ideal for discussing agreement and error. See the separate Venturi tube and the Bernoulli model for related work; contact LabEquip to confirm the set-up, or browse physics lab equipment.

Frequently Asked Questions

What does a Pitot tube actually measure?

The stagnation pressure, the pressure of the fluid brought to rest at its open tip. Subtracting the static pressure from a wall tapping leaves the dynamic pressure, half the density times the speed squared.

What speed does a 5 cm difference in water columns represent?

For flowing water read on water columns, about 1 m/s, from v = √(2gΔh). If air is flowing and the manometer holds water, the same reading means a much higher air speed, because air is far less dense.

Why do the Pitot and Venturi results differ slightly?

The Pitot tube measures the speed at its tip, while the Venturi gives the average over the cross-section. Flow is fastest at the centre of a pipe, so a centred Pitot tube usually reads a little above the mean.

Why must the Pitot tube point straight into the flow?

Only then is the fluid entering it fully brought to rest. If it is angled, part of the flow slips past the opening and the reading falls below the true stagnation pressure.

Where are Pitot tubes used in real life?

On aircraft, where a Pitot-static system feeds the airspeed indicator, on racing cars during testing, and in wind tunnels and ventilation ducts for measuring air flow.

Does the model run on water or air?

The working fluid and flow source can be confirmed at enquiry. The equations are the same for both; only the density in v = √(2Δp/ρ) changes.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
USD United States (US) dollar
Product has been added to your cart
Compare (0)