Quick Answer: The vacuum pump 10 L/min is an electric laboratory pump rated, as its name states, at 10 litres per minute, used to evacuate bell jars and small vessels for air-pressure demonstrations and to provide suction for vacuum filtration. It saves the effort of hand pumping when demonstrations are repeated through the day.
What 10 L/min Means in Practice
The flow rating tells how much air the pump moves each minute when it draws from atmospheric pressure. As the vessel empties, each litre of gas the pump takes in contains fewer molecules, so the pressure drops steeply at first and then ever more gradually. A rough guide is that removing most of the air from a vessel takes several times longer than its volume divided by the flow rate: a 5 litre bell jar is far from empty after half a minute, even though 5 litres have passed through the pump.
How low the pressure finally goes is a separate property, the ultimate vacuum, which depends on the pump design and on leaks in the system. School demonstrations and filtration need only a moderate vacuum, so the flow rate mainly decides how long students wait.
Laboratory Uses
- Evacuating bell jars for air-pressure and sound demonstrations
- Vacuum filtration with a Buchner funnel and filter flask
- Degassing small volumes of liquid before experiments
- Replacing a water aspirator where water use is a concern
Using the Pump Safely and Well
For filtration, connect the vacuum pump 10 L/min to the side arm of a filter flask through a trap bottle so that liquid cannot be drawn into the pump. For bell jar work, use thick-walled vacuum tubing that will not collapse, and fit a valve so the jar can be isolated before the pump is switched off. Corrosive or solvent vapours should not be pumped unless the pump is designed for them.
Specifications
| Item | Electric laboratory vacuum pump |
| Flow rate | 10 L/min, as stated in the product name |
| Uses | Bell jar evacuation, vacuum filtration, degassing small samples |
| Connection | Vacuum tubing to a valve, trap or filter flask |
| Pump type, ultimate vacuum and supply rating | Confirm at enquiry |
Care & Handling
- Always fit a trap between a filtration flask and the pump
- Run the pump on a stable, ventilated surface, leaving space for cooling air
- Do not pump corrosive or solvent-laden vapours unless the pump is rated for them
- Switch off and unplug before cleaning or changing tubing
Why Choose LabEquip
Technicians choose an electric pump of this size when bell jar demonstrations and filtrations happen several times a day and hand pumping slows lessons down. It suits the two-valve vacuum plate with electrical feedthrough; for an oil-free pump that can also supply compressed air, compare the portable diaphragm vacuum pump cum air compressor. More physics lab equipment is in the category, and LabEquip can confirm the supply rating.
Frequently Asked Questions
How long does the pump take to evacuate a bell jar?
It depends on the jar volume, any leaks and the vacuum required. Because the pressure falls roughly exponentially, reaching a good demonstration vacuum takes several times longer than the jar volume divided by 10 litres per minute.
Can the pump be used for vacuum filtration?
Yes. Connect it to the side arm of a filter flask through a trap bottle, so that filtrate or foam cannot reach the pump, and release the vacuum before switching off.
Why does the pressure fall more slowly towards the end?
The pump sweeps roughly the same volume each minute, but at lower pressure that volume contains less gas. The amount of air removed per minute therefore drops as the pressure falls.
Does the pump need oil?
That depends on the pump type. Diaphragm pumps run without oil, while rotary vane pumps need oil changes and an outlet mist filter; confirm the type of this model when you enquire.
Is it safe to use with chemicals?
Use a cold trap or a suitable filter when vapours are present, and avoid pumping corrosive or flammable vapours unless the pump is designed for them. Vapours can condense inside the pump, damaging seals and creating a hazard.
What tubing should be used?
Thick-walled rubber or plastic vacuum tubing that does not collapse under suction. Thin tubing flattens when the pressure inside falls and blocks the flow.
Last Updated: October 2026










Reviews
There are no reviews yet.