Search

In Stock

Special Ball Bearing for Hand Spinner

Roulement à billes spécial hand spinner enables technical analysis of friction vs. velocity curves at the "Analyze" cognitive level, reinforcing evidentiary laboratory practices in university-level physics.

Ruggedized GCr15 Steel Composition Ensures hardware durability during repetitive vocational training cycles, maintaining experimental parity across large-scale student cohorts.

$1.86

Quick Answer: This is a ball bearing made for hand spinners: the round bearing at the centre of a spinner that lets the outer body turn freely around the fingers holding the middle. Schools use the hand spinner ball bearing in design projects where students model and 3D print their own spinner body.

How a Ball Bearing Cuts Friction

A ball bearing replaces sliding with rolling. An inner ring and an outer ring are separated by a ring of hardened balls running in grooved tracks; when one ring turns relative to the other, the balls roll instead of rubbing. Rolling friction is far smaller than sliding friction, so very little energy is lost and the spinner keeps turning for a long time after a flick.

How long it spins depends on what remains. The grease in the bearing, any shields or seals, and air resistance on the spinner arms all take energy away gradually. Students can compare a bearing as supplied with one that has been cleaned of grease, which often spins longer but louder and wears faster.

Specifications

Item Ball bearing for a hand spinner
Construction Inner and outer rings separated by rolling balls
Fitting Pressed into the centre of a spinner body
Used in Design-and-make spinner projects and rotation experiments
Bearing size and pack quantity Confirm at enquiry

Physics with a Hand Spinner

Once the bearing is in a spinner body, the moment of inertia comes into play. Putting mass far from the centre, in weighted arms or an outer ring, raises the moment of inertia, so the spinner stores more rotational energy at the same speed and slows down more gradually. Students can design two bodies of equal mass but different mass distribution, time their spin-down and explain the difference.

A spinning spinner also resists being tilted, a gentle introduction to gyroscopic behaviour and angular momentum: turning the wrist while holding a fast spinner produces a noticeable sideways push. For design work, the body needs a hole that grips the bearing’s outer ring firmly; a hole printed slightly undersize and pressed on usually works better than glue, which can seep into the bearing.

Project and Lesson Uses

  • 3D-printed hand spinner projects
  • Comparing spin-down times for different body designs
  • Introducing rolling versus sliding friction
  • Demonstrating moment of inertia and gyroscopic effects

Care & Handling

  • Keep the bearing clean and away from sand or dust, which roughens the tracks
  • Press it in by the outer ring only, never by the inner ring, to avoid damaging the balls
  • Keep glue and paint away from the gaps between the rings
  • Store bearings dry to prevent rust

Why Choose LabEquip

Technology and physics teachers buy spinner bearings so that every student’s printed design ends up as a working spinner. LabEquip supplies them with other physics lab equipment; ask about the bearing size and quantities through LabEquip contact.

Frequently Asked Questions

Why does a ball bearing spin so freely?

The balls roll between the rings instead of sliding, and rolling friction is much smaller than sliding friction, so little energy is lost on each turn.

How do I fit the bearing into a printed spinner?

Model the centre hole so the outer ring is a firm press fit, then push the bearing in by its outer ring only. Avoid glue, which can creep into the bearing.

Why do spinners with heavy outer arms spin longer?

Mass far from the centre gives a larger moment of inertia, so the spinner stores more energy at a given speed and slows down more gradually.

Should we remove the grease?

Removing grease can make a bearing spin longer but noisier, and it wears faster. Compare both conditions as an experiment rather than cleaning every bearing.

Why does a spinning spinner resist tilting?

A spinning body has angular momentum, and changing its direction needs a turning force. The effect is felt as a sideways push when the wrist is turned.

What size is the bearing?

The listing does not state the size. Tell us the hole size in your spinner design and we will confirm whether this bearing matches.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
USD United States (US) dollar
Product has been added to your cart
Compare (0)