Search

In Stock

Ringtone

Sonnerie features a precision-wound electromagnetic coil and a high-conductivity striker, designed for low-latency hammer actuation and consistent decibel output across varied voltage inputs.

Integrated Montée sur embase (Base-Mounted) Secured to a high-dielectric didactic base with 4mm safety shrouded sockets, providing structural stability and low-resistance connectivity for high-cadence laboratory sessions and complex circuit assembly.

$1.41

Quick Answer: This electric bell ringer is a bell that rings while current flows, using an electromagnet to drive a striker against a gong. In school physics the electric bell ringer is used as a loud output in doorbell and alarm circuits and as an everyday example of electromagnetism.

Ringing From an Electromagnet

The traditional design relies on a make-and-break contact: current through the coil pulls an iron armature, the striker hits the gong, and that movement opens the contact so the electromagnet lets go and a spring returns the armature to close it again. The cycle repeats rapidly for as long as the circuit is closed. The part-by-part action is explained on our electric bell page; here the emphasis is on using the ringer as an output in circuits students design themselves.

Building Alarm Circuits

A bell is the natural output for a circuit that must attract attention. The simplest is a doorbell: a cell, a push switch and the bell in series. From there students can design alarms in which the push switch is replaced by a sensor. A pressure pad under a mat, a reed switch near a magnet on a door, or two wires that touch when a float rises in water each complete the circuit and ring the bell. A latching version, which keeps ringing after the door is shut again, introduces relays and the idea of memory in a circuit.

Sensor-driven alarms need an interface, because a thermistor or light dependent resistor cannot carry the bell’s current itself. A transistor or relay controlled by a potential divider does the switching, so a fire alarm can ring when a thermistor warms or an intruder alarm when a light beam is interrupted. These projects pull several topics together at once: series circuits, sensors, switching and electromagnetism.

Projects With the Ringer

  • Doorbell circuits with a push switch
  • Door alarms using a reed switch and magnet, or a pressure pad
  • Fire or frost alarms switched through a transistor by a thermistor
  • Comparing a bell, an electromagnetic buzzer and a lamp as circuit outputs

Specifications

Type Electric bell (ringer)
Mechanism Electromagnet acting on a striker and gong
Output Audible ringing while the circuit is closed
Use Doorbell and alarm circuits; electromagnetism lessons
Operating voltage and DC or AC use Confirm at enquiry

Care & Handling

  • Run the electric bell ringer only within its stated voltage; overdriving heats the coil and pits the contact.
  • Do not bend the striker arm, since its spacing from the gong decides how cleanly the bell rings.
  • Keep the contact points clean and dry, and do not oil them.
  • Avoid ringing the bell close to anyone’s ear, and keep demonstrations short in small rooms.

Why Choose LabEquip

LabEquip supplies electric ringers to schools that teach alarm-circuit projects and electromagnetism, together with switches, sensors and sources from our physics lab equipment range. Send your supply voltage and quantity through the contact page so the ringer can be matched to your circuits.

Frequently Asked Questions

How does an electric bell keep ringing while the switch is held?

Its contact opens each time the striker moves towards the gong, cutting the current to the electromagnet. A spring then pulls the striker back, the contact closes and the electromagnet pulls again. This repeats many times a second until the switch is released.

Can the bell run on AC as well as DC?

A make-and-break bell will usually ring on either, because it interrupts the current itself, although many bells are designed for one kind of supply. Some AC bells have no contact and vibrate at the supply frequency instead. The supply type and voltage this ringer is intended for should be confirmed at enquiry.

How do I build a door alarm with the bell?

Connect a cell, the bell and a normally closed reed switch in series. A magnet fixed to the door holds the reed switch open while the door is shut; opening the door moves the magnet away, the switch closes and the bell rings.

Why can a thermistor not ring the bell directly?

A bell needs a fairly large current, while a thermistor or light dependent resistor is a sensor that only changes resistance. Using it in a potential divider to control a transistor or relay lets a small sensing current switch the larger current the bell requires.

What is the difference between a bell and a buzzer?

A bell strikes a metal gong with a hammer and gives a loud ring. A buzzer vibrates a small diaphragm and gives a quieter, higher-pitched tone from far less current. Bells suit alarms meant to be heard across a room; buzzers suit bench indicators.

Why does the bell spark at the contact?

When the contact opens, the current in the coil is interrupted suddenly, and the collapsing magnetic field induces a voltage that can jump the small gap. This self-induction is normal in make-and-break bells and slowly wears the contact points.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
USD United States (US) dollar
Product has been added to your cart
Compare (0)