Quick Answer: A rack and pinion test bench is a teaching bench on which a small gear, the pinion, meshes with a straight toothed bar, the rack. Rotating the pinion drives the rack along a straight path, so the rack and pinion test bench shows how rotary motion is converted into linear motion and lets students measure the travel produced by each turn.
From Turning to Sliding
Each tooth of the pinion that passes the mesh pushes the rack along by one tooth pitch. One full turn therefore advances the rack by the pinion’s tooth count times the pitch, which is the same as the circumference of the pinion’s pitch circle, π × pitch diameter. A pinion with 20 teeth on a rack with a 3 mm pitch moves the rack 60 mm per turn. Students check this by turning the pinion a counted number of times and measuring the rack’s travel with a ruler.
The conversion works both ways. Pushing the rack turns the pinion, which is how a rack and pinion can measure a linear movement or be driven from a straight-line actuator.
Force, Handles and Backlash
Turning the pinion with a crank handle multiplies the force. Ignoring friction, the force on the rack equals the force on the handle multiplied by the ratio of handle radius to pinion pitch radius. A 100 mm handle on a 10 mm pitch-radius pinion gives a tenfold force increase, but the hand must move ten times further than the rack.
Reverse the direction of turning and the rack hesitates for a moment before moving back. This free play, called backlash, comes from the small clearance between meshing teeth. It matters in machines that position things accurately, and on the bench it can be measured as the angle the handle turns before the rack responds.
Where Rack and Pinion Is Used
- Car steering, where the steering column turns a pinion on the rack
- Rack railways that climb gradients too steep for wheel grip alone
- The feed handle of a pillar drill and many sliding gates
- Bench measurements of travel per turn and backlash
Specifications
| Mechanism | Pinion gear meshing with a straight toothed rack |
| Motion conversion | Rotation into straight-line travel, and the reverse |
| Travel per pinion turn | Number of pinion teeth × tooth pitch |
| Measurements | Rack travel against turns counted; backlash angle |
| Gear size, travel and drive method | Confirm at enquiry |
Care & Handling
- Keep the teeth free of grit and swarf, which wear the mesh quickly.
- Plastic gears generally run dry; metal teeth take only a thin film of grease.
- Do not force the rack past the end of its travel.
- Store the bench with the rack supported so it cannot bend.
Why Choose LabEquip
Technology teachers studying how mechanisms change one kind of motion into another usually start with rack and pinion, because the conversion is easy to see and measure. LabEquip lists this bench in its physics lab equipment range together with a set of gears and racks for model building and the universal joint test bench. Gear size and drive options can be confirmed through the contact page.
Frequently Asked Questions
What distance does the rack travel per pinion revolution?
It equals the tooth count of the pinion times the pitch of the rack teeth, which is also the circumference of the pinion’s pitch circle. A 20-tooth pinion on a 3 mm pitch rack moves it 60 mm per turn.
Can the rack drive the pinion?
Yes. A rack and pinion is reversible, so pushing the rack turns the pinion. This differs from a worm and wheel, which usually cannot be driven backwards.
Where is rack and pinion used?
Car steering, rack railways, pillar drill feeds, sliding gates and many machine slides. Any task that needs rotation turned into straight-line movement is a candidate.
How does a crank handle increase the force on the rack?
The handle acts as a lever. The force on the rack is the force on the handle multiplied by the handle radius divided by the pinion’s pitch radius, ignoring friction.
Why is there a little free play when the direction is reversed?
There is a small clearance between meshing teeth, called backlash. When the direction changes, the pinion must turn through that clearance before its teeth push the rack the other way.
How should the teeth be looked after?
Keep them clean and free of grit. Plastic gears normally run without lubricant, while metal ones need only a thin film of grease wiped on occasionally.
Last Updated: October 2026










Reviews
There are no reviews yet.