Quick Answer: A stroboscope tachometer is an instrument that measures the rotational speed of a shaft, wheel or fan without touching it. The user adjusts the flash rate of the stroboscope tachometer until a mark on the turning part appears to stand still, and the instrument’s flash rate then gives the speed, usually expressed in revolutions per minute.
Reading a Speed by Stroboscopic Matching
Put a single clear mark, such as a strip of white tape or a chalk line, on the rotating part. Set the flash rate above the expected speed and bring it down until the mark appears once, sharp and stationary. At that point the part makes exactly one revolution between flashes, so the flash rate equals the rotation rate. A flash rate of 25 per second corresponds to 25 revolutions per second, or 1500 rpm.
The trap is that a single still mark also appears at half, a third or a quarter of the true speed, because the part then turns two, three or four times between flashes. Always take the highest flash rate that gives one still mark, and then double it: at twice the true speed, two marks appear half a turn apart. If doubling shows a single mark, the first reading was a sub-multiple.
Where It Has the Advantage
An optical tachometer needs reflective tape on the shaft, and a contact tachometer must touch it. The flash-matching method needs neither, so it suits parts behind a guard or a window, parts too small for tape, and machines that cannot be stopped to fit anything. It also lets the user look at the machine while it runs: a slipping belt, a fluttering blade or a loose coupling shows up clearly when the motion is frozen.
Specifications
| Measurement | Rotational speed by stroboscopic matching |
| Contact with the part | None |
| Reading | Flash rate taken as the rotation rate |
| Also used for | Visual inspection of moving parts while running |
| Range, resolution and power source | Confirm at enquiry |
Applications
- Measuring motor, fan and shaft speeds in physics and engineering laboratories
- Checking the steady speed of a rotating platform during circular-motion work
- Inspecting belts, gears and couplings while they run
- Calibrating the speed setting of a variable-speed drive
Care & Handling
- Remember that a part frozen by the flashes is still turning; never reach towards a machine because it appears stationary.
- Keep the lamp window clean so the flashes reach a distant mark clearly.
- Switch the instrument off when not taking a reading, and store it in its case.
- Check the power source before each session so readings are not interrupted part-way.
Why Choose LabEquip
Engineering workshops and physics laboratories choose this instrument when parts cannot be touched or taped, or when the motion must be watched as well as measured. LabEquip lists it in its physics lab equipment range; the contact and optical tachometer is the simpler choice when tape can be fitted. Send the speeds you need to measure through the contact page.
Frequently Asked Questions
How does a stroboscope tachometer measure speed?
It flashes at an adjustable rate. When the flash rate equals the rotation rate, a mark on the part is lit in the same position each time and appears to stand still, so the flash rate gives the speed.
Why can a reading come out at half the true speed?
At half the true rate the part makes two full turns between flashes and the mark still appears in one place. Taking the highest flash rate that gives a single still mark avoids this error.
How do I check that a reading is correct?
Double the flash rate. At the true speed this shows two marks half a turn apart. If only one mark appears, the original setting was a sub-multiple and the speed is higher.
When is a stroboscope tachometer better than an optical tachometer?
When the part is behind a guard or window, too small for reflective tape, or cannot be stopped to fit tape. It also lets you watch the moving part, which shows faults such as belt slip.
How do I convert a flash rate in hertz into rpm?
Multiply by 60. A flash rate of 25 Hz that freezes a single mark means the shaft turns at 1500 revolutions per minute.
Is it safe to inspect running machinery under strobe light?
Only from a safe distance and with guards in place. The flashes can make a turning part look still, which is dangerous if someone reaches towards it. Flashing light can also affect people with photosensitive epilepsy.
Last Updated: October 2026










Reviews
There are no reviews yet.