Search

In Stock

Ohmmeter

High-Sensitivity PMMC Movement: Features a permanent magnet moving coil assembly with sapphire jewel bearings, ensuring friction-free needle response and superior calibration stability for low-magnitude resistance detection.

Integrated Zero-Ohm Adjustment: Equipped with a precision-wound potentiometer that allows for the compensation of internal lead resistance, ensuring high-resolution accuracy across the non-linear logarithmic scale during sensitive experimental procedures.

₹990.00

Quick Answer: An ohmmeter is a measuring instrument that reads electrical resistance directly, using its own internal cell to pass a small current through the resistor under test. In the physics laboratory it is used to check resistors, wires and components and to show how resistance changes with length, temperature or light.

How an Ohmmeter Works

In the analogue form, a cell, a fixed resistor, an adjustable zero control and a moving-coil movement are connected in series inside the case, with the test leads completing the circuit. With the leads touched together, the resistance outside the meter is zero and the current is greatest; the zero control is set so that this current gives full-scale deflection, marked as zero ohms.

When a resistor is placed between the leads, the total resistance rises and the current falls. A larger resistance means a smaller deflection, so the resistance scale runs the opposite way to a current scale, with zero at the right and higher values towards the left. The scale is also uneven, with divisions crowding together at the high-resistance end, because the current varies inversely with total resistance rather than in proportion to it.

Readings are most reliable near the middle of the scale, where the divisions are widest. Zeroing before each set of readings compensates for the slow fall in the internal cell’s voltage.

Specifications

Type Resistance meter with internal cell
Principle Current from an internal cell through the unknown resistance, read on a resistance scale
Zero setting Adjusted with the test leads shorted together
Use Out-of-circuit measurement of resistors and components
Display type, range and cell Confirm at enquiry

Experiments and Checks

  • Checking the values of resistors before they are used in a circuit
  • Showing that the resistance of a wire increases with its length
  • Following the fall in resistance of an LDR in light or of a thermistor as it warms
  • Testing continuity of leads, fuses and switches
  • Comparing readings with a known decade resistance box setting

Care & Handling

  • Never connect the ohmmeter to a circuit that is switched on; its own cell provides the test current.
  • Re-zero with the leads touched together before each set of readings.
  • Remove the cell if the meter will not be used for a long period.
  • Do not hold both ends of a high-value resistor with your fingers while measuring, since body resistance adds a parallel path.

Why Choose LabEquip

Physics laboratories buy the ohmmeter so students can check components quickly and investigate how resistance depends on physical conditions. It is part of LabEquip’s physics lab equipment range, and display type and range can be confirmed through our contact page.

Frequently Asked Questions

Why does the ohmmeter scale read from right to left?

Zero resistance gives the largest current and full-scale deflection, so zero ohms is at the right. As resistance increases, current and deflection fall, so higher resistances lie towards the left.

Why are the scale divisions crowded at one end?

The current through the meter is inversely related to the total resistance, not proportional to it. Equal steps of resistance therefore give smaller and smaller changes in deflection at the high-resistance end.

Why must the meter be zeroed before use?

The internal cell’s voltage falls slowly with use. Adjusting the zero with the leads shorted sets full-scale deflection to zero ohms again, so later readings stay correct.

Can I measure a resistor while it is in a working circuit?

No. The circuit must be switched off and the component preferably disconnected, because other current paths and the circuit’s own supply would give a false reading and could damage the meter.

Where on the scale is the reading most accurate?

Near the middle, where the divisions are widest. If the pointer sits near either end, choose a different range if the meter has one.

Does my body affect the reading?

With high resistances, yes. Holding both leads or both ends of the resistor adds your body as a parallel path, which lowers the reading. Hold only one end, or use clips.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
INR Indian rupee
Product has been added to your cart
Compare (0)