Quick Answer: The Superior moving coil meter is the higher-grade version of the rectangular-dial, front-terminal moving-coil meter, supplied as an ammeter, milliammeter, microammeter, voltmeter or galvanometer for DC measurements. Senior-school and college laboratories choose it where students record readings for graphs and calculations.
Superior and Standard Grades
The Superior grade shares its layout with the standard rectangular meter: a rectangular scale, terminals on the front panel and a permanent-magnet moving-coil movement. It is the higher-finish model in that pattern. The exact differences in scale, movement and case between the two grades, and the ranges available, should be confirmed at enquiry so that the right grade is ordered for each bench.
Whichever grade is used, the quality of a reading depends heavily on technique, and the points below are what turn a deflection into a reliable number.
Reading an Analogue Meter Accurately
The accuracy of an analogue meter is normally expressed as a percentage of its full-scale deflection. The possible error in amperes or volts is therefore the same anywhere on the scale, which means it is a much larger fraction of a small reading than of a large one. Choosing a range on which the pointer sits in the upper half of the scale keeps that relative error small.
Parallax is the other common error. Look at the pointer square-on, with your eye directly in front of it; where the scale carries a mirror strip, move until the pointer hides its own reflection. Estimate between the smallest divisions, and check the zero before connecting rather than correcting readings afterwards.
Meter Loading
Every meter disturbs the circuit slightly. An ammeter adds its own small resistance in series, and a moving-coil voltmeter draws a little current through its series resistance. In most school circuits these effects are negligible, but with high-value resistors a voltmeter of low resistance can read noticeably low, a useful discussion point in senior practicals.
Specifications
| Type | Permanent-magnet moving-coil meter, Superior grade |
| Dial | Rectangular |
| Terminals | Front panel, polarity marked |
| Versions | Ammeter, milliammeter, microammeter, voltmeter and galvanometer |
| Differences from the standard grade, and ranges | Confirm at enquiry |
Applications
- Verifying Kirchhoff’s laws in networks of resistors
- Measuring the resistivity of a wire from current and voltage readings
- Calibrating an ammeter or voltmeter against a potentiometer
- Recording current against time while a capacitor discharges through a resistor
Care & Handling
- Store the meters flat in a dry cupboard, away from magnets and heat sources.
- Never connect an ammeter range directly across a cell or power supply.
- Clean the window with a soft dry cloth only; solvents can damage plastic covers.
- If a meter has been overloaded, check its zero and compare it with another meter before further use.
Why Choose LabEquip
Laboratories that run graph-based electricity practicals buy the Superior moving coil meter for the benches where results are recorded, and the standard rectangular version for general circuit work. Both are in LabEquip’s physics lab equipment range, and our team can help match grades and ranges through the contact page.
Frequently Asked Questions
Why should the pointer be in the upper half of the scale?
The meter’s possible error is a fixed fraction of full-scale deflection. On a small deflection that same error is a larger proportion of the reading, so choosing a range that gives a large deflection improves the relative accuracy.
How do I avoid parallax error?
Keep your eye directly in front of the pointer. If the scale has a mirror strip, position yourself so that the pointer covers its own reflection before taking the reading.
Does connecting an ammeter change the current being measured?
Slightly, because the ammeter adds its own small resistance to the circuit. In most school circuits the change is negligible, but it becomes noticeable when the circuit resistance itself is very low.
Why might a voltmeter read low across a large resistor?
A moving-coil voltmeter draws a small current. Across a large resistor that current is a significant share of the total, so the voltmeter lowers the voltage it is trying to measure.
Can these meters be checked for accuracy in the laboratory?
Yes. A classic senior practical calibrates an ammeter or voltmeter against a potentiometer, which measures voltage without drawing current, and plots a correction graph for the meter.
Which version is used as a null detector?
The galvanometer version. It is used in meter bridge and potentiometer circuits, where the aim is to find the setting at which no current flows through it.
Last Updated: October 2026










Reviews
There are no reviews yet.