Quick Answer: The Masses (Weights) Set, Slotted, Brass is a set of brass slotted masses, discs with a slot to the centre that slide onto a mass hanger one at a time. A slotted brass masses set is used to load springs, wires and strings in equal steps, most often to find a spring constant.
Spring Constant, Two Ways
The static method is the familiar Hooke’s law practical. A spring hangs from a clamp with a pointer against a vertical scale; slotted masses are added to the hanger one at a time and the extension recorded after each. Plotting load in newtons against extension gives a straight line through the origin while the spring stays within its limit of proportionality, and the gradient is the spring constant k.
The dynamic method uses the same spring and masses. With a load on the hanger, the spring is pulled down slightly and released, and the time for twenty oscillations is measured. For a mass-spring oscillator the period is T = 2π√(m/k), so a graph of T² against m is a straight line with gradient 4π²/k. Comparing the two values of k is a good test of experimental care, and the small intercept on the T² graph reveals the effective mass of the spring itself.
Why Brass
Brass is dense, so each disc is compact and a loaded stack stays short on the hanger. It does not rust in a damp laboratory, and it is non-magnetic, which matters when masses are used near compasses, magnets or electromagnets in force experiments. Its surface darkens with handling, a cosmetic change that a dry cloth keeps in check.
Experiments
- Hooke’s law and spring-constant practicals
- Mass-spring oscillations and the T² against m graph
- Loading wires in Young’s modulus experiments
- Tension in sonometer strings, and loads in pulley or lever experiments
Specifications
| Set type | Slotted masses |
| Material | Brass |
| Form | Discs with a radial slot for a hanger stem |
| Typical companions | Mass hanger, helical springs, clamp stand, metre scale |
| Masses in the set and hanger supply | Confirm at enquiry |
Care & Handling
- Turn the slots of successive discs in opposite directions so the stack cannot slide off the hanger.
- Add the slotted brass masses gently; a dropped load makes a spring overshoot and can overstretch it.
- Keep the discs dry and wipe away fingerprints after use.
- Store the set on its stand or in its box so that every disc stays with the set.
Why Choose LabEquip
Physics departments buy slotted brass sets for every spring station in a practical class, because brass discs stay rust-free through years of use. LabEquip lists this set among its mechanics lab equipment; the cymbal weights set is a related slotted pattern. The number of sets and hanger requirements can be sent through the contact page.
Frequently Asked Questions
How do I find a spring constant with slotted masses?
Add masses to the hanger in equal steps and record the extension after each. Plot the load in newtons against extension; the gradient of the straight part of the graph is the spring constant in newtons per metre.
What is the dynamic method for a spring constant?
Hang a load, set it oscillating vertically and time several oscillations to find the period. Because T = 2π√(m/k), plotting T² against m gives a straight line of gradient 4π²/k, from which k follows.
Why are brass slotted masses preferred over iron ones?
Brass does not rust and is not attracted by magnets, so it keeps its mass and can be used near magnetic apparatus. Iron or painted steel masses are an economical option where neither point matters.
Why stagger the slots when stacking?
If every slot points the same way, a swinging hanger can throw the whole stack off. Alternating the slot direction locks each disc against the one below.
What is the limit of proportionality?
It is the largest load for which extension stays proportional to load. Beyond it the graph curves, and further loading may stretch the spring permanently. Unloading readings that do not return to the loading readings show the limit has been passed.
Can the masses be used without a hanger?
They are designed to sit on a hanger stem through their slot. Without one they can still be placed on a balance pan or a trolley, but hanging loads need a hanger of known mass, and that mass must be added to the total.
Last Updated: October 2026










Reviews
There are no reviews yet.