Search

In Stock

Inclined Plane, Economy

Adjustable Hinged Chassis: Features a 600mm x 100mm kiln-dried hardwood board with a reinforced steel hinge, enabling variable angular settings from 0° to 45° for precise gravitational component analysis.

Integrated Low-Friction Pulley: Equipped with a 35mm diameter frictionless plastic pulley mounted on a stable end-bracket, ensuring consistent tension and minimal energy loss during load-and-effort experimental cycles.

$5.47

Quick Answer: The economy inclined plane is a simple adjustable slope with an angle scale, the basic model in the inclined plane range. It is used in junior and middle-school science to explore the ramp as a simple machine, comparing the effort needed to move a load up a slope with the force needed to lift it straight up.

The Ramp as a Simple Machine

The inclined plane is one of the classic simple machines, and the economy model concentrates on that idea. Pulling a load up a gentle ramp takes less force than lifting it vertically, but the load must be moved further along the slope. Students can feel this before they calculate it: a spring balance attached to a trolley or block reads less on a shallow slope than when the same load is hung from it directly.

Measuring the effort at several angles shows the pattern. The steeper the ramp, the larger the effort, until at a vertical slope the effort equals the full weight. The ratio of load to effort is the mechanical advantage, and for a smooth ramp it equals the length of the slope divided by the height gained.

Multiplying the effort by the distance moved along the slope and comparing it with the load multiplied by the height gives the work done in each case. The two are nearly equal, and the small difference is the work done against friction, an early introduction to the idea of efficiency.

Activities for Junior Classes

  • Comparing the force to drag a load up a ramp with the force to lift it
  • Measuring how effort changes as the slope becomes steeper
  • Calculating mechanical advantage from load and effort, and from length and height
  • Comparing work done along the slope with work done lifting vertically
  • Relating ramps to wheelchair access ramps and loading ramps for vehicles

Specifications

Type Adjustable inclined plane, economy model
Angle reading Angle scale on the plane, as the listing indicates
Effort measurement Spring balance, or pulley and pan where fitted
Level Junior and middle-school science
Accessories included Confirm at enquiry

Care & Handling

  • Set the plane on a flat bench and support it fully before placing loads on it.
  • Keep spring balances at zero and replace any that stick.
  • Wipe the surface clean so friction stays the same from one lesson to the next.
  • Fold or lower the plane for storage to protect its hinge and scale.

Why Choose LabEquip

Primary and middle schools buy the economy inclined plane to introduce simple machines with real measurements at low cost per group, and the larger adjustable inclined plane model suits demonstrations. LabEquip lists both with its physics lab equipment, and accessories for each group can be confirmed through our contact page.

Frequently Asked Questions

Why is less force needed to push a load up a ramp?

Only part of the load’s weight acts along the slope. The effort has to overcome that part, plus friction, rather than the whole weight, but it must act over a longer distance.

What is the mechanical advantage of an inclined plane?

It is the load divided by the effort. For a smooth ramp it equals the length of the slope divided by the vertical height it rises.

Does a ramp save work?

No. It reduces the force needed but increases the distance. Ignoring friction, the work done along the ramp equals the work done lifting the load straight up.

How can effort be measured without a pulley?

Attach a spring balance to the load and pull it slowly and steadily up the slope, keeping the balance parallel to the surface. The reading is the effort.

Is the economy model suitable for senior practicals?

It suits introductory work on simple machines. Senior experiments on resolving forces or friction coefficients are better served by the brass or deluxe models with a roller, pulley and pan.

What everyday machines work like an inclined plane?

Wedges, screws and ramps all use the inclined plane principle. A screw thread, for example, is an inclined plane wrapped around a cylinder.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
USD United States (US) dollar
Product has been added to your cart
Compare (0)