Search

In Stock

Fluid Pressure Apparatus (Spouting Cylinder)

Tri-Level Orifice Configuration: Features three precision-machined, vertically aligned discharge nozzles at equidistantly spaced heights, enabling the simultaneous observation of varying parabolic fluid trajectories relative to the water column height.

Reinforced Metallic Housing: Constructed from heavy-gauge, anti-corrosive sheet metal with an integrated overflow management system and a stable weighted base to ensure rigid verticality during high-volume discharge cycles.

$6.77

Quick Answer: The Fluid Pressure Apparatus (Spouting Cylinder) is a tall water container with outlets at different heights down one side, used to show that pressure in a liquid increases with depth. Water spurts out of the lower holes faster than out of the upper ones, because the pressure behind each jet depends on the depth of water above it.

Pressure, Depth and Jet Speed

The pressure at a depth h in a still liquid exceeds the surface pressure by ρgh, so it grows steadily as you go down. In a spouting cylinder each side outlet feeds a jet whose speed reflects that pressure. By Torricelli’s theorem the water leaves at a speed of about √(2gh), the speed it would gain falling freely through the depth h, so a hole four times as deep gives a jet twice as fast.

Where the jets land is a richer question than it first seems. A jet from low down leaves fast but has little height to fall, so it lands sooner; a jet from near the top falls far but leaves slowly. If the jets land on the level of the cylinder’s base, the range is 2√(h·y), where y is the height of the hole above that level, and the greatest range comes from a hole halfway down the water column. Students who predict that the lowest jet goes farthest are often surprised, which makes this a good prediction exercise.

Each jet also leaves at right angles to the wall, showing that liquid pressure acts in all directions, not only downward. To keep the jets steady during measurement, the water level must be held constant by topping up. The Bernoulli tube apparatus carries the story on to moving liquids. Typical spouting cylinders are sheet-metal tubes with equal-sized holes; the number of outlets, material and height of this one are not stated in its title.

Demonstrations

  • Showing that pressure increases with depth in middle-school science
  • Predicting and then testing which jet lands farthest
  • Checking Torricelli’s theorem by measuring jet range at a constant head
  • Explaining why dams are built thicker at the base

Specifications

Demonstration Liquid pressure increases with depth
Principle p = ρgh; jet speed √(2gh) by Torricelli’s theorem
Usual form Tall cylinder with equal side outlets at different heights
Working liquid Water, optionally coloured
Number of outlets, material and height Confirm at enquiry

Care & Handling

  • Stand the cylinder in a sink or a large tray, as the jets travel some distance.
  • Close the outlets with stoppers or tape while filling, then open them together.
  • Keep the water level constant during measurements by topping up.
  • Clear the outlets of debris or scale so that each jet leaves cleanly.
  • Empty and dry the cylinder after use.

Why Choose LabEquip

Science teachers use the spouting cylinder because a single pour of water shows pressure varying with depth to a whole class. It sits in our Physics Equipments; contact LabEquip for outlet and size details.

Frequently Asked Questions

Why does water come out faster from the lower holes?

Pressure in a liquid increases with depth because more water presses down from above. The lower holes have a greater depth of water above them, so the water is pushed out at a higher speed.

Does the lowest jet always travel farthest?

No. A low jet is fast but has little height to fall before it lands, so it may not reach far. When the jets land at the level of the cylinder’s base, the hole halfway down the water column gives the longest range.

What is Torricelli’s theorem?

It states that liquid flows out of a small hole at a depth h below the surface with a speed of about the square root of 2gh, the same speed an object would gain falling freely through that height.

Why must the water level be kept constant?

As the cylinder drains, the depth above each hole falls and the jets weaken. Topping up keeps the head constant so that the jets stay steady while they are measured.

Why do the jets come out at right angles to the wall?

Liquid pressure acts equally in all directions at a given depth and pushes perpendicular to any surface it meets. At each hole it drives water straight out, normal to the wall.

What everyday examples does this explain?

Dams are thicker at the bottom because water pressure is greatest there, water tanks are placed high to give good pressure at taps, and a leak low in a container spurts harder than one near the top.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
USD United States (US) dollar
Product has been added to your cart
Compare (0)