Quick Answer: This electromagnetic ripple tank is a water-wave tank whose ripples are generated by an electromagnetic vibrator, a coil-and-magnet driver fed from a signal generator, so the frequency of the waves can be set and read. It shows mechanical waves on water; the word electromagnetic describes the drive, not the waves.
An Electromagnetic Drive for Water Waves
The vibrator works on the same principle as a loudspeaker: alternating current in a coil near a magnet makes the coil, and the arm attached to it, move back and forth at the frequency of the current. The arm carries a dipper that touches the water, so each cycle of the electrical signal produces one ripple. Because the frequency is set electronically, it is steady and can be changed in fine steps.
Different dippers on the arm give different sources: a straight bar for plane waves, a single point for circular waves, and two points for a pair of sources vibrating in step. Raising the frequency shortens the wavelength in proportion, so students can verify v = fλ for water waves by measuring λ at several settings.
Measurements the Tank Supports
- Verifying v = fλ for water waves at several frequencies
- Measuring the refractive index of a shallow region from wavelength ratios
- Linking the spacing of two-source interference lines to wavelength
- Showing the Doppler effect with a moving source
Experiments That Need a Known Frequency
Knowing the frequency turns every ripple tank effect into a measurement. Refraction over a shallow plate can be quantified by measuring the wavelength on both sides and taking the ratio, which equals the ratio of the speeds and so the refractive index for water waves. In interference, the spacing of the calm lines depends on the wavelength and the source separation, so changing the frequency and watching the pattern open out or close up links the tank directly to Young’s slits.
Where the vibrator can be moved, the electromagnetic ripple tank also demonstrates the Doppler effect: a point source carried slowly across the tank while it vibrates leaves wavefronts bunched ahead and spread out behind. A light flashing at the vibrator frequency, where the tank provides one, freezes these patterns for measurement.
Specifications
| Item | Ripple tank with an electromagnetic vibrator |
| Wave generation | Coil-and-magnet vibrator driving a dipper |
| Frequency control | From a signal generator, so it can be set and read |
| Sources | Plane, point and double dippers |
| Shows | Reflection, refraction, diffraction, interference, Doppler effect |
| Generator, light source and accessories | Confirm at enquiry |
Care & Handling
- Keep the vibrator and generator connections dry and away from the edge of the water
- Start at low amplitude, as an overdriven dipper splashes and breaks up the pattern
- Clean the dippers and the tank after use and store them dry
- Switch off the signal generator before changing dippers
Why Choose LabEquip
Senior-school and college physics departments choose this tank when wave lessons need numbers as well as pictures. LabEquip offers it alongside the LED ripple tank kit within its physics lab equipment range; send your generator details through LabEquip contact.
Frequently Asked Questions
Does this tank show electromagnetic waves?
No. It shows water waves. The word electromagnetic refers to the vibrator that makes the ripples, which uses a coil and magnet driven by an electrical signal.
Why is a signal-generator drive useful?
The frequency of the ripples equals the frequency of the electrical signal, so it can be set precisely and read from the generator, which makes wavelength and speed measurements possible.
How do I show the Doppler effect?
Move a vibrating point source slowly across the tank, where the vibrator can be moved. Wavefronts crowd together ahead of the source and spread out behind it.
How is the refractive index for water waves found?
Measure the wavelength in the deep and shallow regions at the same frequency. The ratio of the wavelengths equals the ratio of the speeds, which is the refractive index between the two regions.
Why do the interference lines move closer together at higher frequency?
Higher frequency means a shorter wavelength, and the angle between lines of calm water depends on the wavelength divided by the spacing of the sources.
What else do I need to run the tank?
A signal generator if one is not supplied, a light source and screen, and clean water. Tell us what you already have and we will confirm what the set needs.
Last Updated: October 2026










Reviews
There are no reviews yet.