Search

In Stock

Electronic Daniell Cell 1.08 Volt DC Regulated

Original price was: $11.84.Current price is: $5.81.

Quick Answer: The Electronic Daniell Cell 1.08 Volt DC Regulated is an electronic Daniell cell that provides a regulated 1.08 V DC output, standing in for the classic zinc-copper Daniell cell so physics classes can work with a steady, known EMF without preparing solutions.

Why a Fixed 1.08 V Is Useful

The Daniell cell, introduced by John Frederic Daniell in 1836, places a zinc electrode in zinc sulfate solution and a copper electrode in copper sulfate solution, separated by a porous pot or salt bridge. Zinc is oxidised (Zn → Zn²⁺ + 2e⁻) and copper ions are reduced (Cu²⁺ + 2e⁻ → Cu), and the cell is written Zn | Zn²⁺ || Cu²⁺ | Cu. Its standard EMF is about 1.10 V, and many school physics texts quote 1.08 V for the cell as used in the laboratory.

A chemical Daniell cell drifts as its solutions change concentration and its electrodes age, and every group’s cell ends up slightly different. The electronic version provides the regulated 1.08 V named in its title, so every bench starts from the same value. That makes it a convenient known EMF: in a potentiometer experiment, balancing this cell first calibrates the wire, and an unknown EMF can then be found from E = 1.08 × l2 / l1, where l1 and l2 are the balancing lengths for the reference and unknown cells.

Historically the Daniell cell mattered because it did not polarise the way earlier copper-zinc cells did, so it could supply a steady current for telegraph systems. That contrast with the Leclanché cell, which polarises under continuous load, is still a standard comparison in physics and chemistry classes.

Specifications

Apparatus Electronic Daniell cell
Output (from product name) 1.08 V DC, regulated
Represents Zinc-copper Daniell primary cell
Main uses Known EMF for potentiometer work; EMF comparison with a Leclanché cell
Current limit and terminal type Confirm at enquiry
Use Supervised physics and electrochemistry practicals

Applications

  • Comparing the EMFs of a Daniell and a Leclanché cell with a potentiometer
  • Acting as the reference cell when measuring an unknown EMF
  • A low-voltage DC source for voltmeter reading and polarity exercises
  • Electrochemistry lessons that contrast the textbook wet cell with a steady electronic reference

Care & Handling

  • Connect the positive terminal to the same end of the potentiometer wire as the driver cell’s positive terminal, or no balance point will be found.
  • Do not short the terminals or connect the unit to another power supply.
  • Keep it dry and away from the solutions used in wet-cell practicals.
  • Store it in a dry cupboard between practical sessions.

Why Choose LabEquip

Physics labs usually buy this unit with the Electronic Leclanche Cell for the two-cell EMF comparison, while schools that also want students to build a wet cell use the Simple Cell Pot. All three belong to our Electrical and Electronics range; the LabEquip contact page is where to say how many potentiometer set-ups you run.

Frequently Asked Questions

Why is the output set at 1.08 V?

1.08 V is the EMF that many school physics texts give for a Daniell cell, close to its standard value of about 1.10 V. Using the same figure means results can be checked directly against the textbook.

What reactions take place in a traditional Daniell cell?

Zinc atoms lose electrons and enter the zinc sulfate solution as zinc ions, while copper ions gain electrons from the circuit and are deposited as copper metal on the copper electrode.

How can the 1.08 V cell be used as a reference in a potentiometer experiment?

Find the balancing length l1 for the 1.08 V cell, then the balancing length l2 for the unknown cell. The unknown EMF equals 1.08 multiplied by l2 divided by l1.

Why was the Daniell cell an improvement on earlier cells?

Earlier simple cells polarised quickly as hydrogen bubbles formed on the copper plate. In the Daniell cell, copper is deposited instead of hydrogen, so it gives a much steadier current.

Can the electronic unit replace a chemical Daniell cell in electrochemistry practicals?

For EMF and circuit work, yes. Practicals that study the electrodes, solutions or salt bridge themselves still need a real cell made with zinc, copper and their sulfate solutions.

What precautions apply when using the cell?

Use it under supervision, connect it with the correct polarity, never short the terminals and keep it away from water and wet-cell solutions.

Last Updated: October 2026

Bestsellers

Discrete Electronics Trainer Kit

Original price was: $67.68.Current price is: $33.73.
(0 Reviews)

Electronic Daniell Cell 1.08 Volt DC Regulated

Original price was: $11.84.Current price is: $5.81.
(0 Reviews)

Electrical Resistance Combination Apparatus

Original price was: $19.18.Current price is: $9.48.
(0 Reviews)

Battery Eliminator AC/DC 12V 2A

Original price was: $17.37.Current price is: $8.57.
(0 Reviews)

Transistor Performance Evaluation Apparatus

Original price was: $34.97.Current price is: $17.37.
(0 Reviews)

Digital Logic Trainer with Built-In Voltmeter

Original price was: $117.31.Current price is: $58.54.
(0 Reviews)

Electronic Power Supply System

Original price was: $15.79.Current price is: $7.78.
(0 Reviews)

Back to Top
Select your currency
USD United States (US) dollar
Product has been added to your cart
Compare (0)