Search

In Stock

Electric Bell

Electromagnetic coil with spring-loaded striker mechanism illustrating rapid switching action

Low-voltage operating design suitable for safe classroom and laboratory demonstrations

$3.16

Quick Answer: The Electric Bell is a working bell in which an electromagnet, a soft-iron armature and a make-and-break contact keep a hammer striking a metal gong for as long as current flows. Physics teachers use the electric bell to show a practical application of electromagnetism and a circuit that switches itself on and off.

Inside the Bell

Most bells of this kind have two coils wound on a U-shaped iron core, so that both poles of the electromagnet face the armature and pull on it together. The armature is a small block of soft iron fixed to a springy steel strip, and the strip carries the hammer at its tip. Current enters through one terminal, passes round the coils, along the strip and out through a pointed contact screw that rests against it.

Pressing the switch energises the coils. The armature is drawn towards the poles and the hammer strikes the gong, but in moving, the strip lifts off the contact screw. With no current, the core stops attracting, the strip springs back to rest against the screw, current flows once more and the hammer is pulled in again. This trembler action produces a rapid series of strikes that continues until the switch is released.

What Controls the Ring

The rate of striking depends on how stiff the spring strip is, how heavy the armature and hammer are, and how far the strip must travel before it leaves the contact. The contact screw sets that travel. Turned in too far, the strip cannot break away and the hammer stays pressed against the gong; turned out too far, the strip never closes the circuit. Small adjustments while the bell is connected give a clear, steady sound.

The supply matters too. A weak cell gives a feeble current, the core pulls the armature only weakly and the bell sounds faint or stops. Too high a voltage overheats the coils and erodes the contact. The bell’s rated voltage should therefore be checked and matched with cells or a low-voltage bench supply.

Specifications

Type Make-and-break (trembler) bell with hammer and gong
Main parts Two-coil electromagnet, soft-iron armature on spring strip, contact screw, gong
Operation Strikes repeatedly while the circuit is closed
Typical supply Low-voltage direct current from cells or a bench supply
Rated voltage, gong size and mounting Confirm at enquiry

Lessons and Projects

  • Demonstrating the magnetic effect of a current and the pull of an electromagnet on soft iron
  • Explaining self-interrupting circuits as an introduction to relays and buzzers
  • Building door, burglar or flood alarms with push switches, reed switches or pressure pads in design and technology projects
  • Investigating how cell voltage affects the loudness and rate of striking

Care & Handling

  • Connect the bell only to a low-voltage supply at its rated voltage, never to the mains.
  • Clean a blackened or pitted contact with fine emery paper, then reset the screw for a steady ring.
  • Avoid leaving it ringing for long periods; the coils warm up and the contact wears faster.
  • Fix the base firmly to a board or wall so the gong rings clearly and the bell does not rattle.

Why Choose LabEquip

Schools buy electric bells for electromagnetism demonstrations and for student alarm and circuit projects. LabEquip lists this bell in its physics lab equipment range; the separate electromagnet lets students study the bell’s key component on its own. Ask about rated voltage and mounting via our contact page.

Frequently Asked Questions

How does an electric bell keep ringing?

Each time the hammer is pulled in, the spring strip lifts off the contact screw and the current stops. The strip springs back, touches the screw, current flows again and the hammer is pulled in once more, so the strikes repeat rapidly.

Why do most bells have two coils on a U-shaped core?

The U shape puts both magnetic poles close to the armature, so both pull on it at once. This gives a much stronger pull for the same current than a single straight coil, which only presents one pole.

What sets how fast the hammer strikes?

The stiffness of the spring strip, the mass of the armature and hammer, and the distance the strip moves before the contact opens. A stiffer spring or a smaller gap gives faster, lighter strikes.

Why does the bell sound weak when the cells are old?

Old cells supply less current, so the electromagnet is weaker and pulls the armature with less force. The hammer strikes the gong gently, or not at all if the pull cannot overcome the spring.

How can the bell be used in an alarm circuit?

Connect it with a supply and one or more switches. Several push or reed switches wired in parallel make the bell ring when any one of them closes, which is how a simple door or window alarm works.

How is a buzzer different from an electric bell?

An electromagnetic buzzer uses the same make-and-break action but has no hammer and gong; the vibrating armature itself makes the sound. Many modern buzzers instead use a piezoelectric disc driven by an electronic circuit.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
USD United States (US) dollar
Product has been added to your cart
Compare (0)