Quick Answer: Crocodile clip jumper wires are short flexible leads with a spring-loaded crocodile clip at each end, shown in the product photograph as a bundle in red, yellow, green, black and other colours. They make quick, temporary connections to component legs, electrodes, cells and terminals in school circuit work.
Fast Connections Without Terminals
Many items in a science lab have no proper terminal: a lemon with copper and zinc strips, an LED with bare legs, a pencil lead used as a resistor, a coin in a conductivity test. Crocodile clip jumper wires connect to all of them. The serrated jaws grip wires, rods, strips and edges, the spring holds them shut, and the lead between the clips is flexible enough to reach across a bench.
The colours have a practical job. Using red for connections to the positive side and black for negative, with the remaining colours for links between components, makes a circuit easier to follow and check. With several colours, a teacher can ask students to trace a single path through a circuit by colour, which makes errors stand out.
Where Jumper Leads Reach Their Limits
Each clip touches the conductor at a few points, so the contact resistance is higher and less predictable than a screwed or plugged joint. For most circuits with lamps, motors and LEDs this is unimportant, but in precise measurements, such as finding the resistance of a short length of wire, a fraction of an ohm at each clip affects the result. In that case, connect the voltmeter directly across the wire being tested rather than across the clips. Jumper leads are for low-voltage work only and are never used on mains equipment. For a sturdier, fully covered clip, see the insulated crocodile clips.
Applications
- Fruit and vegetable cell experiments with metal electrodes
- Testing conductors and insulators by clipping across samples
- Quick series and parallel circuits with lamps, LEDs and motors
- Connecting sensors and components with bare legs to meters and data loggers
Specifications
| Product | Jumper leads with crocodile clips |
| Ends | Crocodile clip at each end |
| Colours | Several, as in the product photograph |
| Lead | Flexible insulated wire |
| Use | Temporary low-voltage connections |
| Number of leads and length | Confirm at enquiry |
Care & Handling
- Open the clips by squeezing the handles rather than pulling them off a connection
- Untangle the leads after each lesson and hang or box them by colour
- Check for broken wires at the clip ends, the point where most leads fail
- Do not use the leads for mains voltage or high-current circuits
Why Choose LabEquip
Primary and secondary schools buy crocodile clip jumper wires in bulk, often to top up electricity experiment kits for schools whose leads have gone missing over a term. LabEquip can supply them by the class set; ask through our contact page, and see the black alligator clip test leads and other physics lab equipment.
Frequently Asked Questions
Why do jumper leads come in different colours?
Colours make circuits easier to read and check. A common scheme uses red for positive, black for negative and other colours for the links between components, so students can trace a path quickly.
Can the leads be used to connect to a lemon battery?
Yes. Clip one lead to a copper strip and another to a zinc or galvanised strip pushed into the fruit, then connect the other ends to a sensitive meter or a low-current LED.
Why does my resistance measurement change when I move the clips?
Each clip adds a small contact resistance that varies with how it grips. For accurate readings on a low-resistance sample, connect the voltmeter directly across the sample and keep the clips firmly closed.
Are crocodile clip leads safe for mains use?
No. They are intended only for low-voltage circuits such as cells, battery holders and low-voltage power supplies. Their clips and insulation are not designed for mains.
How should the leads be stored?
Hang them on a rack or keep them in a box by colour after untangling. Leaving them in a heap leads to knots and broken wires near the clips.
Can a broken lead be repaired?
If the wire has parted at a clip, it can be stripped back and re-fixed to the clip by crimping or soldering. Leads with damaged insulation along their length should be replaced.
Last Updated: October 2026










Reviews
There are no reviews yet.