Search

In Stock

Clamping Nut with Suspension Hook

Noix de serrage avec crochet de suspension, Integrated Steel Suspension Hook enables precise Analysis of gravitational loads and mechanical advantage when coupled with StemAids pulleys or dynamometers.

High-Torque Ergonomic Thumb-Screws ensure the safety and stability of experimental rigs, allowing for student Evaluation of rotational equilibrium without mechanical drift.

$2.59

Quick Answer: A boss head with suspension hook is a clamping block that tightens onto a retort stand rod with a screw and carries a built-in hook. The boss head with suspension hook gives a firm, height-adjustable point on the stand from which springs, pendulums, pulleys and force meters can be hung.

One Part Instead of Three

Hanging a spring from a stand usually needs a boss head, a short rod and a hook or clamp. The boss head with suspension hook combines them: slide it onto the stand rod, tighten the screw at the required height and hang the load directly. With fewer joints there is less to slip, and the suspension point sits close to the stand rod.

Because it slides along the rod, the hook can be set to any height. That is useful when a spring has to clear the bench by a set distance or when a pendulum length must be adjusted in steps.

Keeping the Stand Upright

A load on the hook pulls down slightly to one side of the stand rod, so it produces a turning effect about the edge of the stand base. The stand stays upright as long as the moment of the stand’s own weight about that edge is larger. Turning the hook so the load hangs over the base, rather than beyond it, removes most of the problem.

For heavier loads or long rods, clamp the base to the bench or place a weight on it. The same reasoning is a neat applied example of the principle of moments for students.

Specifications

Product Boss head (clamping block) with built-in suspension hook
Mounting Clamps onto a vertical stand rod with a tightening screw
Function Height-adjustable suspension point
Used with Springs, pendulums, pulleys, force meters, mass hangers
Rod diameter accepted Confirm at enquiry

Typical Uses

  • Hanging springs for Hooke’s law experiments
  • Suspending a simple pendulum at an adjustable height
  • Supporting a pulley on its bracket for pulley systems
  • Holding a force meter for weighing and upthrust experiments

Care & Handling

  • Tighten the screw firmly before loading and check that the boss cannot slide
  • Keep the stand rod clean and dry; oil or polish lets the boss slip
  • Do not over-tighten on thin-walled rods, which can dent
  • Store with the screw backed off so its thread does not seize

Why Choose LabEquip

Physics teachers buy boss heads with hooks in quantity because almost every spring, pendulum and pulley practical needs a suspension point. LabEquip supplies them alongside the pulley on bracket and other physics lab equipment for complete stand set-ups; send LabEquip your quantities.

Frequently Asked Questions

How is this different from an ordinary boss head?

An ordinary boss head joins two rods and needs a separate hook or clamp to hang a load. This one has the hook built in, so it gives a suspension point on the stand rod in one piece.

Which stand rods will it fit?

The rod diameter it accepts can be confirmed at enquiry. Matching it to the rods already in your lab makes sure it clamps squarely and holds firmly.

Why does the boss slip down the rod under load?

Either the screw is not tight enough or the rod is greasy or polished. The hanging load also tries to twist the boss, so tighten it firmly and clean the rod.

How can the stand be stopped from tipping over?

Turn the hook so the load hangs over the stand base, keep the boss low on the rod where possible, and clamp the base to the bench or weight it for heavier loads.

Is a hook good enough as a pendulum suspension?

For a quick demonstration, yes. For accurate timing, clamp the thread between two flat surfaces so the swinging length is fixed; a loop on a hook can roll and change the length.

Can two hooks be used on one rod?

Yes. Two boss heads with hooks at different heights let a spring hang from one while a pointer or a second spring hangs from the other, or support two pendulums side by side.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
USD United States (US) dollar
Product has been added to your cart
Compare (0)