Search

In Stock

Capillary Tube Apparatus

Multi-bore Borosilicate Array: Comprises four distinct, precision-drawn glass capillaries with graduated internal diameters ranging from 0.5mm to 2.0mm to provide high-contrast visual data.

Leak-Proof Reservoir Assembly: Mounted on a heavy-duty, chemically resistant base featuring a central trough that ensures uniform liquid distribution and stability during sensitive measurements.

₹475.00

Quick Answer: The Capillary Tube Apparatus is a demonstration set of glass capillary tubes of different bores standing in the same liquid, used to show capillary rise: liquid climbs higher in narrower tubes. It illustrates surface tension and Jurin’s law, which says the height of rise is inversely proportional to the tube radius.

Why Liquid Rises Higher in Narrower Tubes

Water wets clean glass, so at the edge of its surface the liquid meets the tube wall at a very small contact angle and curves up into a concave meniscus. Surface tension acting around the circle of contact pulls the column up until its weight balances that pull. Equating the two forces gives h = 2T cos θ / (rρg), where T is surface tension, θ the contact angle, r the bore radius and ρ the liquid density.

Because h varies as 1/r, a tube with half the radius lifts the liquid twice as high, and standing several tubes side by side in one reservoir shows this at a glance: the levels step upward from the widest tube to the finest. Coloured water makes the columns easy to see from the back of a room. A liquid that does not wet glass, such as mercury, shows the opposite effect, a depression below the outside level with a convex meniscus.

For a measured value of surface tension rather than a demonstration, a single capillary is held in a capillary tube clamp above a rising table and the rise is read with a travelling microscope. The number of tubes, their bores and the stand or trough supplied with this capillary tube apparatus are not stated in its title.

Specifications

Demonstration Capillary rise and its dependence on bore
Principle Surface tension; h = 2T cos θ / (rρg)
Usual layout Glass capillary tubes of different bores dipping in a common liquid
Typical liquid Water, often coloured for visibility
Number of tubes, bores and stand Confirm at enquiry

Demonstrations

  • Showing that capillary rise is inversely proportional to tube radius
  • Explaining everyday capillarity in lamp wicks, blotting paper and moist soil
  • Comparing a wetting liquid with a non-wetting one through the shape of the meniscus
  • Adding a drop of detergent to show that lower surface tension means a lower rise

Care & Handling

  • Clean the tubes with detergent solution and rinse thoroughly with distilled water; grease on the glass reduces the rise.
  • Wet the bores by dipping the tubes deeper and then raising them, so the columns settle from above rather than climbing a dry wall.
  • Handle the capillaries gently, as their fine ends chip easily.
  • Drain and dry the tubes after use to prevent dye stains and mineral deposits in the bores.

Why Choose LabEquip

Teachers introducing surface tension in middle and secondary classes use this set because the effect of bore size is visible to the whole class at once. It is part of our physics lab equipment range; contact LabEquip for tube and stand details.

Frequently Asked Questions

Why does water rise higher in a narrower tube?

The upward pull of surface tension acts around the circumference of the meniscus, which is proportional to the radius, while the weight of the raised column depends on its cross-sectional area, proportional to the radius squared. A smaller radius therefore needs a taller column for the weight to balance the pull.

Why does mercury fall instead of rising in a glass capillary?

Mercury does not wet glass. Its contact angle is greater than 90 degrees, so the surface-tension force points downward and the level inside the tube is depressed below the outside surface.

Why add colour to the water?

Plain water in a fine tube is hard to see from a distance. A little dye makes each column stand out; use only a small amount so that the surface tension is not noticeably changed.

Why do dirty tubes give lower readings?

Grease or residue on the glass increases the contact angle, so the water no longer wets the wall fully and the upward pull is reduced. Clean tubes are essential for a clear demonstration.

Can this apparatus measure surface tension?

It demonstrates the principle and the inverse dependence on radius. A numerical value needs an accurately known bore and a precise height measurement, normally made with a single capillary, a travelling microscope and a rising table.

What happens if detergent is added to the water?

Detergent lowers the surface tension of water, so the columns in all the tubes drop. This is a quick way to show that capillary rise depends on surface tension.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
INR Indian rupee
Product has been added to your cart
Compare (0)