Search

In Stock

Cantilever Apparatus

Reinforced Rigid Clamp Assembly: Features a heavy-duty, cast-iron mounting base with a precision-machined G-clamp mechanism, ensuring zero-slip anchorage for consistent, one-end-fixed beam stabilization during intensive load testing.

Integrated Measurement Interface: Designed with a secondary support pillar to house a high-resolution spherometer or micrometer, enabling sub-millimeter quantification of longitudinal deflection across diverse metallurgical samples and cross-sectional geometries.

$7.39

Quick Answer: A cantilever apparatus holds a uniform beam rigidly clamped at one end so that loads can be hung from its free end. The depression of the free end is measured for each load, and from it the Young’s modulus of the beam material is calculated.

Principle of the Loaded Cantilever

A cantilever is a beam fixed firmly at one end and free at the other, the arrangement found in diving boards, balconies and aircraft wings. A load at the free end bends the beam, and the free end drops by an amount called the depression. Theory shows that the depression is proportional to the load and to the cube of the length, and inversely proportional to the Young’s modulus, the breadth and the cube of the thickness.

Those cube relationships make the cantilever very sensitive to length and thickness. Doubling the length increases the depression eightfold; doubling the thickness reduces it to one-eighth. In the laboratory this means a modest load on a thin strip gives a depression large enough to measure, and that the thickness must be measured with care.

The depression is usually read with a travelling microscope focused on a pin or mark at the free end, or with a vernier scale attached to the beam. Readings are taken for increasing and then decreasing loads, and the mean depression per unit load comes from the slope of a graph.

A Typical Run

Clamp the beam with a fixed length projecting, hang the weight hanger near the free end and focus the microscope on the reference mark. Add equal loads in steps, recording the microscope reading after each, then remove them in the same steps. Measure the projecting length with a metre rule, the breadth with vernier callipers and the thickness at several points with a screw gauge.

Applications

  • Determining the Young’s modulus of a metal or wooden strip
  • Verifying that depression is proportional to load within the elastic limit
  • Investigating how depression depends on the cube of the projecting length
  • Studying the oscillations of a loaded cantilever

Specifications

Type Cantilever: beam rigidly clamped at one end
Loading Weight hanger at the free end
Measurement Depression of the free end, read with a microscope or vernier
Quantity found Young’s modulus of the beam material
Beams, clamp and reading device supplied Confirm at enquiry

Care & Handling

  • Tighten the clamp firmly; any movement at the clamped end adds to the measured depression.
  • Stay within loads from which the beam returns to its starting reading.
  • Store beams flat to prevent a permanent set or twist.
  • Avoid knocking the bench during readings, as the microscope magnifies every vibration.

Why Choose LabEquip

Senior-school and college laboratories buy the cantilever apparatus for a direct, easily understood Young’s modulus practical, and many add Koenig’s bending of beam apparatus for the optical method. LabEquip lists both in its physics lab equipment, and our team can be reached through the contact page.

Frequently Asked Questions

What is a cantilever?

A beam fixed rigidly at one end and free at the other. Everyday examples include diving boards, shelves on brackets and balconies.

Why does the depression depend so strongly on length?

The bending effect of the load increases with distance from the clamp, and the beam’s slope builds up along its length. Together these make the depression proportional to the cube of the projecting length.

How is the depression measured?

Usually with a travelling microscope focused on a pin or mark at the free end, or with a vernier scale fixed to the beam. The difference between readings with and without the load gives the depression.

Why must the beam be clamped very firmly?

Any rotation or slip at the clamped end lowers the free end in addition to the true bending, giving a larger depression and too low a value of Young’s modulus.

Can the cantilever be made to oscillate?

Yes. A loaded cantilever set vibrating oscillates with a period that depends on its stiffness and the load, which offers a dynamic way to find its elastic properties.

Which beam materials are suitable?

Uniform strips of steel, brass, aluminium or wood are commonly used. The material should bend elastically and return to its original position when unloaded.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
USD United States (US) dollar
Product has been added to your cart
Compare (0)