Quick Answer: The Fixed 50 Ohm Resistor is a component with a fixed resistance of 50 ohms, used in school and college laboratories as a known resistance in circuit experiments. A 50 ohm resistor serves in Ohm’s law practicals, in series and parallel combinations, as a current-limiting resistor and as a matched load for signal generators.
A Known Resistance in a Circuit
A fixed resistor converts electrical energy into heat at a steady, predictable rate, and its resistance stays essentially constant over the currents used in teaching circuits. That makes it the reference against which students test Ohm’s law: with the resistor in series with an ammeter and a voltmeter across it, the ratio of voltage to current should come out close to 50 ohms at every setting, and the current-voltage graph should be a straight line through the origin.
Combining it with other resistors shows the rules for networks. Two of these resistors in series give 100 ohms; in parallel they give 25 ohms. Students can predict these values and then confirm them with a multimeter or a decade resistance box for comparison.
Power Rating and Matched Loads
Every resistor has a power rating, the heat it can safely dissipate. The power is the square of the current times the resistance, so at 100 mA this resistor dissipates half a watt, and at 300 mA it dissipates 4.5 watts. If the dissipation exceeds the rating the resistor overheats and its value drifts or it fails; the power rating, tolerance and mounting of this item should be confirmed so it suits the currents planned.
Fifty ohms also has a special place in signal work. Many signal generators are designed to drive a 50 ohm load, and connecting a 50 ohm resistor across the output, a termination, keeps the output amplitude well defined, as when using an A.F./R.F. oscillator for filter or resonance measurements.
Practicals
- Verifying Ohm’s law with an ammeter and voltmeter
- Building series and parallel resistor networks
- Limiting current to a lamp, LED or meter while a circuit is set up
- Providing a known load when finding the internal resistance of a cell
- Terminating a signal generator output at 50 ohms
Specifications
| Resistance | 50 ohms, fixed (from the title) |
| Type | Fixed resistor for teaching circuits |
| Behaviour | Ohmic: current proportional to voltage at constant temperature |
| Key limit | Power rating, P = I squared R |
| Power rating, tolerance and mounting | Confirm at enquiry |
Care & Handling
- Work out the power before switching on and keep it within the resistor rating.
- Let the resistor cool before touching it after carrying a large current.
- Check its value with a multimeter from time to time; overheating can shift the resistance.
- Keep terminals clean and tight, as loose connections add resistance.
Why Choose LabEquip
Teachers buy fixed resistors of standard values so every bench can check the same calculation, and 50 ohms is a convenient value for both DC circuits and signal-generator work. LabEquip lists it among its physics equipment, and quantities or mounting styles can be discussed through the contact page.
Frequently Asked Questions
What is the resistance of two 50 ohm resistors in parallel?
25 ohms. For two equal resistors in parallel the combined value is half of one; in series it would be 100 ohms.
How much current can the resistor carry?
That depends on its power rating. The maximum safe current is the square root of the power rating divided by 50; for a 1 watt rating that is about 140 mA.
Why does the measured resistance differ slightly from 50 ohms?
Every resistor is made within a tolerance, and its value also changes a little with temperature. Small differences are normal; a large difference suggests damage from overheating.
Why is 50 ohms used to terminate signal generators?
Many signal generators and coaxial cables are designed around 50 ohms. A matching load keeps the output voltage defined and reduces reflections in fast or high-frequency signals.
Is a fixed resistor an ohmic conductor?
Yes, at constant temperature. Its current-voltage graph is a straight line through the origin, unlike a filament lamp, whose resistance rises as it heats.
How is the resistor used to protect a meter or LED?
Placed in series, it limits the current that can flow when the supply is connected, so a meter or LED is not overloaded while the rest of the circuit is adjusted.
Last Updated: October 2026










Reviews
There are no reviews yet.