Search

In Stock

BULB 3V

Rated operating voltage of 3 volts DC, compatible with battery-based and low-voltage lab circuits

Durable filament construction with controlled resistance, ensuring predictable illumination behavior

$1.86

Quick Answer: This 3V bulb is a miniature filament bulb rated for 3 volts, the voltage of two cells in series. Schools use the 3V bulb in two-cell circuits, in series and parallel brightness comparisons and, with meters and a variable resistor, to plot the curved current–voltage graph of a filament.

A Filament That Does Not Obey Ohm’s Law

A metal wire kept at constant temperature has a straight current–voltage graph: double the voltage and the current doubles. The tungsten filament inside the bulb does not stay at constant temperature. As the voltage rises, the filament heats from room temperature towards white heat, its resistance rises several times over, and the graph of current against voltage bends over towards the voltage axis. This is the standard example of a non-ohmic component in school physics.

The experiment needs the bulb, a variable supply or a 25 ohm variable resistor connected as a potential divider, an ammeter in series and a voltmeter across the bulb. Readings are taken from zero up to the 3 V rating, and resistance is calculated at each point as V/I. The cold resistance, measured with a multimeter before the circuit is switched on, is far lower than the working value, which explains why filament lamps draw a surge of current at the instant they are switched on and why they often fail at that moment.

The 3 V rating matches two cells in series, so the bulb also suits primary and middle school circuit work. Two such bulbs in series on two cells glow dimly, sharing the voltage, while two in parallel each receive the full 3 V and glow normally. Run below its rating the bulb glows dull red, a direct way to see that brightness depends on the power delivered.

Uses

  • Plotting the I–V characteristic of a filament and calculating its resistance at each voltage
  • Comparing the cold and hot resistance of the filament
  • Series and parallel lamp circuits on two cells
  • Showing that brightness depends on the power delivered to the bulb
  • Indicator lamps in models, alarms and circuit projects

Specifications

Component Miniature filament bulb
Rated voltage 3 V, as titled, matching two cells in series
Behaviour Non-ohmic: resistance rises as the filament heats
Used with Bulb holders on circuit boards and in circuit kits
Base type and current rating Confirm at enquiry

Care & Handling

  • Run the 3V bulb at or below 3 V; above its rating the filament overheats and fails.
  • Let a hot bulb cool before removing it from its holder, and handle it by the base.
  • Store spare bulbs in a padded box, because the filament breaks easily if dropped.
  • If a bulb fails to light, check the cells, the holder contacts and the wiring before replacing it.

Why Choose LabEquip

Schools buy 3V bulbs by the box for two-cell circuits and for the I–V characteristic practical. For single-cell circuits choose the 1.5V lamp, and see LabEquip’s physics lab equipment for holders and circuit boards. Request pack quantities through the contact page.

Frequently Asked Questions

Why is the I-V graph of a bulb curved?

As the current increases, the filament gets hotter and its resistance rises. Each extra volt then produces a smaller increase in current than the one before, so the graph bends towards the voltage axis instead of staying straight.

Why do bulbs often fail when they are switched on?

A cold filament has a much lower resistance than a hot one, so a surge of current flows at the instant of switch-on. Any thin, weak spot in the filament heats fastest and can break at that moment.

What happens if the bulb is connected to one cell?

It glows, but dimly, because it receives about half its rated voltage and much less than its rated power. That makes a useful comparison with a 1.5 V lamp, which glows fully on one cell.

How is the filament resistance found at full brightness?

Run the bulb at 3 V with an ammeter in series and a voltmeter across it, then divide the voltage by the current. The answer is much larger than the resistance measured cold with a multimeter.

Can LEDs replace filament bulbs in class circuits?

They can show that a circuit is complete, but they behave differently. An LED conducts in one direction only, needs a series resistor and gives a very different I-V graph, so filament bulbs remain the standard for the non-ohmic resistance practical.

Does the bulb get hot?

Yes. Most of the electrical energy becomes heat rather than light, and the glass warms within a minute or two of use. At 3 V it is safe to handle once it has cooled for a short while.

Last Updated: October 2026

Reviews

There are no reviews yet.

Write a review

Back to Top
Select your currency
USD United States (US) dollar
Product has been added to your cart
Compare (0)